blob: b38360e5fe4fa28f0fac24f9cb530b097fdcf4ea [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/************************************************************************/
2/* */
3/* dc395x.h */
4/* */
5/* Device Driver for Tekram DC395(U/UW/F), DC315(U) */
6/* PCI SCSI Bus Master Host Adapter */
7/* (SCSI chip set used Tekram ASIC TRM-S1040) */
8/* */
9/************************************************************************/
10#ifndef DC395x_H
11#define DC395x_H
12
13/************************************************************************/
14/* */
15/* Initial values */
16/* */
17/************************************************************************/
18#define DC395x_MAX_CMD_QUEUE 32
19/* #define DC395x_MAX_QTAGS 32 */
20#define DC395x_MAX_QTAGS 16
21#define DC395x_MAX_SCSI_ID 16
22#define DC395x_MAX_CMD_PER_LUN DC395x_MAX_QTAGS
23#define DC395x_MAX_SG_TABLESIZE 64 /* HW limitation */
24#define DC395x_MAX_SG_LISTENTRY 64 /* Must be equal or lower to previous */
25 /* item */
26#define DC395x_MAX_SRB_CNT 63
27/* #define DC395x_MAX_CAN_QUEUE 7 * DC395x_MAX_QTAGS */
28#define DC395x_MAX_CAN_QUEUE DC395x_MAX_SRB_CNT
29#define DC395x_END_SCAN 2
30#define DC395x_SEL_TIMEOUT 153 /* 250 ms selection timeout (@ 40 MHz) */
31#define DC395x_MAX_RETRIES 3
32
33#if 0
34#define SYNC_FIRST
35#endif
36
37#define NORM_REC_LVL 0
38
39/************************************************************************/
40/* */
41/* Various definitions */
42/* */
43/************************************************************************/
44#define BIT31 0x80000000
45#define BIT30 0x40000000
46#define BIT29 0x20000000
47#define BIT28 0x10000000
48#define BIT27 0x08000000
49#define BIT26 0x04000000
50#define BIT25 0x02000000
51#define BIT24 0x01000000
52#define BIT23 0x00800000
53#define BIT22 0x00400000
54#define BIT21 0x00200000
55#define BIT20 0x00100000
56#define BIT19 0x00080000
57#define BIT18 0x00040000
58#define BIT17 0x00020000
59#define BIT16 0x00010000
60#define BIT15 0x00008000
61#define BIT14 0x00004000
62#define BIT13 0x00002000
63#define BIT12 0x00001000
64#define BIT11 0x00000800
65#define BIT10 0x00000400
66#define BIT9 0x00000200
67#define BIT8 0x00000100
68#define BIT7 0x00000080
69#define BIT6 0x00000040
70#define BIT5 0x00000020
71#define BIT4 0x00000010
72#define BIT3 0x00000008
73#define BIT2 0x00000004
74#define BIT1 0x00000002
75#define BIT0 0x00000001
76
77/* UnitCtrlFlag */
78#define UNIT_ALLOCATED BIT0
79#define UNIT_INFO_CHANGED BIT1
80#define FORMATING_MEDIA BIT2
81#define UNIT_RETRY BIT3
82
83/* UnitFlags */
84#define DASD_SUPPORT BIT0
85#define SCSI_SUPPORT BIT1
86#define ASPI_SUPPORT BIT2
87
88/* SRBState machine definition */
89#define SRB_FREE 0x0000
90#define SRB_WAIT 0x0001
91#define SRB_READY 0x0002
92#define SRB_MSGOUT 0x0004 /* arbitration+msg_out 1st byte */
93#define SRB_MSGIN 0x0008
94#define SRB_EXTEND_MSGIN 0x0010
95#define SRB_COMMAND 0x0020
96#define SRB_START_ 0x0040 /* arbitration+msg_out+command_out */
97#define SRB_DISCONNECT 0x0080
98#define SRB_DATA_XFER 0x0100
99#define SRB_XFERPAD 0x0200
100#define SRB_STATUS 0x0400
101#define SRB_COMPLETED 0x0800
102#define SRB_ABORT_SENT 0x1000
103#define SRB_DO_SYNC_NEGO 0x2000
104#define SRB_DO_WIDE_NEGO 0x4000
105#define SRB_UNEXPECT_RESEL 0x8000
106
107/************************************************************************/
108/* */
109/* ACB Config */
110/* */
111/************************************************************************/
112#define HCC_WIDE_CARD 0x20
113#define HCC_SCSI_RESET 0x10
114#define HCC_PARITY 0x08
115#define HCC_AUTOTERM 0x04
116#define HCC_LOW8TERM 0x02
117#define HCC_UP8TERM 0x01
118
119/* ACBFlag */
120#define RESET_DEV BIT0
121#define RESET_DETECT BIT1
122#define RESET_DONE BIT2
123
124/* DCBFlag */
125#define ABORT_DEV_ BIT0
126
127/* SRBstatus */
128#define SRB_OK BIT0
129#define ABORTION BIT1
130#define OVER_RUN BIT2
131#define UNDER_RUN BIT3
132#define PARITY_ERROR BIT4
133#define SRB_ERROR BIT5
134
135/* SRBFlag */
136#define DATAOUT BIT7
137#define DATAIN BIT6
138#define RESIDUAL_VALID BIT5
139#define ENABLE_TIMER BIT4
140#define RESET_DEV0 BIT2
141#define ABORT_DEV BIT1
142#define AUTO_REQSENSE BIT0
143
144/* Adapter status */
145#define H_STATUS_GOOD 0
146#define H_SEL_TIMEOUT 0x11
147#define H_OVER_UNDER_RUN 0x12
148#define H_UNEXP_BUS_FREE 0x13
149#define H_TARGET_PHASE_F 0x14
150#define H_INVALID_CCB_OP 0x16
151#define H_LINK_CCB_BAD 0x17
152#define H_BAD_TARGET_DIR 0x18
153#define H_DUPLICATE_CCB 0x19
154#define H_BAD_CCB_OR_SG 0x1A
155#define H_ABORT 0x0FF
156
157/* SCSI BUS Status byte codes */
158#define SCSI_STAT_GOOD 0x0 /* Good status */
159#define SCSI_STAT_CHECKCOND 0x02 /* SCSI Check Condition */
160#define SCSI_STAT_CONDMET 0x04 /* Condition Met */
161#define SCSI_STAT_BUSY 0x08 /* Target busy status */
162#define SCSI_STAT_INTER 0x10 /* Intermediate status */
163#define SCSI_STAT_INTERCONDMET 0x14 /* Intermediate condition met */
164#define SCSI_STAT_RESCONFLICT 0x18 /* Reservation conflict */
165#define SCSI_STAT_CMDTERM 0x22 /* Command Terminated */
166#define SCSI_STAT_QUEUEFULL 0x28 /* Queue Full */
167#define SCSI_STAT_UNEXP_BUS_F 0xFD /* Unexpect Bus Free */
168#define SCSI_STAT_BUS_RST_DETECT 0xFE /* Scsi Bus Reset detected */
169#define SCSI_STAT_SEL_TIMEOUT 0xFF /* Selection Time out */
170
171/* Sync_Mode */
172#define SYNC_WIDE_TAG_ATNT_DISABLE 0
173#define SYNC_NEGO_ENABLE BIT0
174#define SYNC_NEGO_DONE BIT1
175#define WIDE_NEGO_ENABLE BIT2
176#define WIDE_NEGO_DONE BIT3
177#define WIDE_NEGO_STATE BIT4
178#define EN_TAG_QUEUEING BIT5
179#define EN_ATN_STOP BIT6
180
181#define SYNC_NEGO_OFFSET 15
182
183/* SCSI MSG BYTE */
184#define MSG_COMPLETE 0x00
185#define MSG_EXTENDED 0x01
186#define MSG_SAVE_PTR 0x02
187#define MSG_RESTORE_PTR 0x03
188#define MSG_DISCONNECT 0x04
189#define MSG_INITIATOR_ERROR 0x05
190#define MSG_ABORT 0x06
191#define MSG_REJECT_ 0x07
192#define MSG_NOP 0x08
193#define MSG_PARITY_ERROR 0x09
194#define MSG_LINK_CMD_COMPL 0x0A
195#define MSG_LINK_CMD_COMPL_FLG 0x0B
196#define MSG_BUS_RESET 0x0C
197#define MSG_ABORT_TAG 0x0D
198#define MSG_SIMPLE_QTAG 0x20
199#define MSG_HEAD_QTAG 0x21
200#define MSG_ORDER_QTAG 0x22
201#define MSG_IGNOREWIDE 0x23
202#define MSG_IDENTIFY 0x80
203#define MSG_HOST_ID 0xC0
204
205/* SCSI STATUS BYTE */
206#define STATUS_GOOD 0x00
207#define CHECK_CONDITION_ 0x02
208#define STATUS_BUSY 0x08
209#define STATUS_INTERMEDIATE 0x10
210#define RESERVE_CONFLICT 0x18
211
212/* cmd->result */
213#define STATUS_MASK_ 0xFF
214#define MSG_MASK 0xFF00
215#define RETURN_MASK 0xFF0000
216
217/************************************************************************/
218/* */
219/* Inquiry Data format */
220/* */
221/************************************************************************/
222struct ScsiInqData
223{ /* INQ */
224 u8 DevType; /* Periph Qualifier & Periph Dev Type */
225 u8 RMB_TypeMod; /* rem media bit & Dev Type Modifier */
226 u8 Vers; /* ISO, ECMA, & ANSI versions */
227 u8 RDF; /* AEN, TRMIOP, & response data format */
228 u8 AddLen; /* length of additional data */
229 u8 Res1; /* reserved */
230 u8 Res2; /* reserved */
231 u8 Flags; /* RelADr, Wbus32, Wbus16, Sync, etc. */
232 u8 VendorID[8]; /* Vendor Identification */
233 u8 ProductID[16]; /* Product Identification */
234 u8 ProductRev[4]; /* Product Revision */
235};
236
237 /* Inquiry byte 0 masks */
238#define SCSI_DEVTYPE 0x1F /* Peripheral Device Type */
239#define SCSI_PERIPHQUAL 0xE0 /* Peripheral Qualifier */
240 /* Inquiry byte 1 mask */
241#define SCSI_REMOVABLE_MEDIA 0x80 /* Removable Media bit (1=removable) */
242 /* Peripheral Device Type definitions */
243 /* See include/scsi/scsi.h */
244#define TYPE_NODEV SCSI_DEVTYPE /* Unknown or no device type */
245#ifndef TYPE_PRINTER /* */
246# define TYPE_PRINTER 0x02 /* Printer device */
247#endif /* */
248#ifndef TYPE_COMM /* */
249# define TYPE_COMM 0x09 /* Communications device */
250#endif
251
252/************************************************************************/
253/* */
254/* Inquiry flag definitions (Inq data byte 7) */
255/* */
256/************************************************************************/
257#define SCSI_INQ_RELADR 0x80 /* device supports relative addressing */
258#define SCSI_INQ_WBUS32 0x40 /* device supports 32 bit data xfers */
259#define SCSI_INQ_WBUS16 0x20 /* device supports 16 bit data xfers */
260#define SCSI_INQ_SYNC 0x10 /* device supports synchronous xfer */
261#define SCSI_INQ_LINKED 0x08 /* device supports linked commands */
262#define SCSI_INQ_CMDQUEUE 0x02 /* device supports command queueing */
263#define SCSI_INQ_SFTRE 0x01 /* device supports soft resets */
264
265#define ENABLE_CE 1
266#define DISABLE_CE 0
267#define EEPROM_READ 0x80
268
269/************************************************************************/
270/* */
271/* The PCI configuration register offset for TRM_S1040 */
272/* */
273/************************************************************************/
274#define TRM_S1040_ID 0x00 /* Vendor and Device ID */
275#define TRM_S1040_COMMAND 0x04 /* PCI command register */
276#define TRM_S1040_IOBASE 0x10 /* I/O Space base address */
277#define TRM_S1040_ROMBASE 0x30 /* Expansion ROM Base Address */
278#define TRM_S1040_INTLINE 0x3C /* Interrupt line */
279
280/************************************************************************/
281/* */
282/* The SCSI register offset for TRM_S1040 */
283/* */
284/************************************************************************/
285#define TRM_S1040_SCSI_STATUS 0x80 /* SCSI Status (R) */
286#define COMMANDPHASEDONE 0x2000 /* SCSI command phase done */
287#define SCSIXFERDONE 0x0800 /* SCSI SCSI transfer done */
288#define SCSIXFERCNT_2_ZERO 0x0100 /* SCSI SCSI transfer count to zero */
289#define SCSIINTERRUPT 0x0080 /* SCSI interrupt pending */
290#define COMMANDABORT 0x0040 /* SCSI command abort */
291#define SEQUENCERACTIVE 0x0020 /* SCSI sequencer active */
292#define PHASEMISMATCH 0x0010 /* SCSI phase mismatch */
293#define PARITYERROR 0x0008 /* SCSI parity error */
294
295#define PHASEMASK 0x0007 /* Phase MSG/CD/IO */
296#define PH_DATA_OUT 0x00 /* Data out phase */
297#define PH_DATA_IN 0x01 /* Data in phase */
298#define PH_COMMAND 0x02 /* Command phase */
299#define PH_STATUS 0x03 /* Status phase */
300#define PH_BUS_FREE 0x05 /* Invalid phase used as bus free */
301#define PH_MSG_OUT 0x06 /* Message out phase */
302#define PH_MSG_IN 0x07 /* Message in phase */
303
304#define TRM_S1040_SCSI_CONTROL 0x80 /* SCSI Control (W) */
305#define DO_CLRATN 0x0400 /* Clear ATN */
306#define DO_SETATN 0x0200 /* Set ATN */
307#define DO_CMDABORT 0x0100 /* Abort SCSI command */
308#define DO_RSTMODULE 0x0010 /* Reset SCSI chip */
309#define DO_RSTSCSI 0x0008 /* Reset SCSI bus */
310#define DO_CLRFIFO 0x0004 /* Clear SCSI transfer FIFO */
311#define DO_DATALATCH 0x0002 /* Enable SCSI bus data input (latched) */
312/* #define DO_DATALATCH 0x0000 */ /* KG: DISable SCSI bus data latch */
313#define DO_HWRESELECT 0x0001 /* Enable hardware reselection */
314
315#define TRM_S1040_SCSI_FIFOCNT 0x82 /* SCSI FIFO Counter 5bits(R) */
316#define TRM_S1040_SCSI_SIGNAL 0x83 /* SCSI low level signal (R/W) */
317
318#define TRM_S1040_SCSI_INTSTATUS 0x84 /* SCSI Interrupt Status (R) */
319#define INT_SCAM 0x80 /* SCAM selection interrupt */
320#define INT_SELECT 0x40 /* Selection interrupt */
321#define INT_SELTIMEOUT 0x20 /* Selection timeout interrupt */
322#define INT_DISCONNECT 0x10 /* Bus disconnected interrupt */
323#define INT_RESELECTED 0x08 /* Reselected interrupt */
324#define INT_SCSIRESET 0x04 /* SCSI reset detected interrupt */
325#define INT_BUSSERVICE 0x02 /* Bus service interrupt */
326#define INT_CMDDONE 0x01 /* SCSI command done interrupt */
327
328#define TRM_S1040_SCSI_OFFSET 0x84 /* SCSI Offset Count (W) */
329
330/************************************************************************/
331/* */
332/* Bit Name Definition */
333/* --------- ------------- ---------------------------- */
334/* 07-05 0 RSVD Reversed. Always 0. */
335/* 04 0 OFFSET4 Reversed for LVDS. Always 0. */
336/* 03-00 0 OFFSET[03:00] Offset number from 0 to 15 */
337/* */
338/************************************************************************/
339
340#define TRM_S1040_SCSI_SYNC 0x85 /* SCSI Synchronous Control (R/W) */
341#define LVDS_SYNC 0x20 /* Enable LVDS synchronous */
342#define WIDE_SYNC 0x10 /* Enable WIDE synchronous */
343#define ALT_SYNC 0x08 /* Enable Fast-20 alternate synchronous */
344
345/************************************************************************/
346/* */
347/* SYNCM 7 6 5 4 3 2 1 0 */
348/* Name RSVD RSVD LVDS WIDE ALTPERD PERIOD2 PERIOD1 PERIOD0 */
349/* Default 0 0 0 0 0 0 0 0 */
350/* */
351/* Bit Name Definition */
352/* --------- ------------- --------------------------- */
353/* 07-06 0 RSVD Reversed. Always read 0 */
354/* 05 0 LVDS Reversed. Always read 0 */
355/* 04 0 WIDE/WSCSI Enable wide (16-bits) SCSI */
356/* transfer. */
357/* 03 0 ALTPERD/ALTPD Alternate (Sync./Period) mode. */
358/* */
359/* @@ When this bit is set, */
360/* the synchronous period bits 2:0 */
361/* in the Synchronous Mode register */
362/* are used to transfer data */
363/* at the Fast-20 rate. */
364/* @@ When this bit is unset, */
365/* the synchronous period bits 2:0 */
366/* in the Synchronous Mode Register */
367/* are used to transfer data */
368/* at the Fast-10 rate (or Fast-40 w/ LVDS). */
369/* */
370/* 02-00 0 PERIOD[2:0]/ Synchronous SCSI Transfer Rate. */
371/* SXPD[02:00] These 3 bits specify */
372/* the Synchronous SCSI Transfer */
373/* Rate for Fast-20 and Fast-10. */
374/* These bits are also reset */
375/* by a SCSI Bus reset. */
376/* */
377/* For Fast-10 bit ALTPD = 0 and LVDS = 0 */
378/* and bit2,bit1,bit0 is defined as follows : */
379/* */
380/* 000 100ns, 10.0 MHz */
381/* 001 150ns, 6.6 MHz */
382/* 010 200ns, 5.0 MHz */
383/* 011 250ns, 4.0 MHz */
384/* 100 300ns, 3.3 MHz */
385/* 101 350ns, 2.8 MHz */
386/* 110 400ns, 2.5 MHz */
387/* 111 450ns, 2.2 MHz */
388/* */
389/* For Fast-20 bit ALTPD = 1 and LVDS = 0 */
390/* and bit2,bit1,bit0 is defined as follows : */
391/* */
392/* 000 50ns, 20.0 MHz */
393/* 001 75ns, 13.3 MHz */
394/* 010 100ns, 10.0 MHz */
395/* 011 125ns, 8.0 MHz */
396/* 100 150ns, 6.6 MHz */
397/* 101 175ns, 5.7 MHz */
398/* 110 200ns, 5.0 MHz */
399/* 111 250ns, 4.0 MHz KG: Maybe 225ns, 4.4 MHz */
400/* */
401/* For Fast-40 bit ALTPD = 0 and LVDS = 1 */
402/* and bit2,bit1,bit0 is defined as follows : */
403/* */
404/* 000 25ns, 40.0 MHz */
405/* 001 50ns, 20.0 MHz */
406/* 010 75ns, 13.3 MHz */
407/* 011 100ns, 10.0 MHz */
408/* 100 125ns, 8.0 MHz */
409/* 101 150ns, 6.6 MHz */
410/* 110 175ns, 5.7 MHz */
411/* 111 200ns, 5.0 MHz */
412/* */
413/************************************************************************/
414
415#define TRM_S1040_SCSI_TARGETID 0x86 /* SCSI Target ID (R/W) */
416#define TRM_S1040_SCSI_IDMSG 0x87 /* SCSI Identify Message (R) */
417#define TRM_S1040_SCSI_HOSTID 0x87 /* SCSI Host ID (W) */
418#define TRM_S1040_SCSI_COUNTER 0x88 /* SCSI Transfer Counter 24bits(R/W) */
419
420#define TRM_S1040_SCSI_INTEN 0x8C /* SCSI Interrupt Enable (R/W) */
421#define EN_SCAM 0x80 /* Enable SCAM selection interrupt */
422#define EN_SELECT 0x40 /* Enable selection interrupt */
423#define EN_SELTIMEOUT 0x20 /* Enable selection timeout interrupt */
424#define EN_DISCONNECT 0x10 /* Enable bus disconnected interrupt */
425#define EN_RESELECTED 0x08 /* Enable reselected interrupt */
426#define EN_SCSIRESET 0x04 /* Enable SCSI reset detected interrupt */
427#define EN_BUSSERVICE 0x02 /* Enable bus service interrupt */
428#define EN_CMDDONE 0x01 /* Enable SCSI command done interrupt */
429
430#define TRM_S1040_SCSI_CONFIG0 0x8D /* SCSI Configuration 0 (R/W) */
431#define PHASELATCH 0x40 /* Enable phase latch */
432#define INITIATOR 0x20 /* Enable initiator mode */
433#define PARITYCHECK 0x10 /* Enable parity check */
434#define BLOCKRST 0x01 /* Disable SCSI reset1 */
435
436#define TRM_S1040_SCSI_CONFIG1 0x8E /* SCSI Configuration 1 (R/W) */
437#define ACTIVE_NEGPLUS 0x10 /* Enhance active negation */
438#define FILTER_DISABLE 0x08 /* Disable SCSI data filter */
439#define FAST_FILTER 0x04 /* ? */
440#define ACTIVE_NEG 0x02 /* Enable active negation */
441
442#define TRM_S1040_SCSI_CONFIG2 0x8F /* SCSI Configuration 2 (R/W) */
443#define CFG2_WIDEFIFO 0x02 /* */
444
445#define TRM_S1040_SCSI_COMMAND 0x90 /* SCSI Command (R/W) */
446#define SCMD_COMP 0x12 /* Command complete */
447#define SCMD_SEL_ATN 0x60 /* Selection with ATN */
448#define SCMD_SEL_ATN3 0x64 /* Selection with ATN3 */
449#define SCMD_SEL_ATNSTOP 0xB8 /* Selection with ATN and Stop */
450#define SCMD_FIFO_OUT 0xC0 /* SCSI FIFO transfer out */
451#define SCMD_DMA_OUT 0xC1 /* SCSI DMA transfer out */
452#define SCMD_FIFO_IN 0xC2 /* SCSI FIFO transfer in */
453#define SCMD_DMA_IN 0xC3 /* SCSI DMA transfer in */
454#define SCMD_MSGACCEPT 0xD8 /* Message accept */
455
456/************************************************************************/
457/* */
458/* Code Command Description */
459/* ---- ---------------------------------------- */
460/* 02 Enable reselection with FIFO */
461/* 40 Select without ATN with FIFO */
462/* 60 Select with ATN with FIFO */
463/* 64 Select with ATN3 with FIFO */
464/* A0 Select with ATN and stop with FIFO */
465/* C0 Transfer information out with FIFO */
466/* C1 Transfer information out with DMA */
467/* C2 Transfer information in with FIFO */
468/* C3 Transfer information in with DMA */
469/* 12 Initiator command complete with FIFO */
470/* 50 Initiator transfer information out sequence without ATN */
471/* with FIFO */
472/* 70 Initiator transfer information out sequence with ATN */
473/* with FIFO */
474/* 74 Initiator transfer information out sequence with ATN3 */
475/* with FIFO */
476/* 52 Initiator transfer information in sequence without ATN */
477/* with FIFO */
478/* 72 Initiator transfer information in sequence with ATN */
479/* with FIFO */
480/* 76 Initiator transfer information in sequence with ATN3 */
481/* with FIFO */
482/* 90 Initiator transfer information out command complete */
483/* with FIFO */
484/* 92 Initiator transfer information in command complete */
485/* with FIFO */
486/* D2 Enable selection */
487/* 08 Reselection */
488/* 48 Disconnect command with FIFO */
489/* 88 Terminate command with FIFO */
490/* C8 Target command complete with FIFO */
491/* 18 SCAM Arbitration/ Selection */
492/* 5A Enable reselection */
493/* 98 Select without ATN with FIFO */
494/* B8 Select with ATN with FIFO */
495/* D8 Message Accepted */
496/* 58 NOP */
497/* */
498/************************************************************************/
499
500#define TRM_S1040_SCSI_TIMEOUT 0x91 /* SCSI Time Out Value (R/W) */
501#define TRM_S1040_SCSI_FIFO 0x98 /* SCSI FIFO (R/W) */
502
503#define TRM_S1040_SCSI_TCR0 0x9C /* SCSI Target Control 0 (R/W) */
504#define TCR0_WIDE_NEGO_DONE 0x8000 /* Wide nego done */
505#define TCR0_SYNC_NEGO_DONE 0x4000 /* Synchronous nego done */
506#define TCR0_ENABLE_LVDS 0x2000 /* Enable LVDS synchronous */
507#define TCR0_ENABLE_WIDE 0x1000 /* Enable WIDE synchronous */
508#define TCR0_ENABLE_ALT 0x0800 /* Enable alternate synchronous */
509#define TCR0_PERIOD_MASK 0x0700 /* Transfer rate */
510
511#define TCR0_DO_WIDE_NEGO 0x0080 /* Do wide NEGO */
512#define TCR0_DO_SYNC_NEGO 0x0040 /* Do sync NEGO */
513#define TCR0_DISCONNECT_EN 0x0020 /* Disconnection enable */
514#define TCR0_OFFSET_MASK 0x001F /* Offset number */
515
516#define TRM_S1040_SCSI_TCR1 0x9E /* SCSI Target Control 1 (R/W) */
517#define MAXTAG_MASK 0x7F00 /* Maximum tags (127) */
518#define NON_TAG_BUSY 0x0080 /* Non tag command active */
519#define ACTTAG_MASK 0x007F /* Active tags */
520
521/************************************************************************/
522/* */
523/* The DMA register offset for TRM_S1040 */
524/* */
525/************************************************************************/
526#define TRM_S1040_DMA_COMMAND 0xA0 /* DMA Command (R/W) */
527#define DMACMD_SG 0x02 /* Enable HW S/G support */
528#define DMACMD_DIR 0x01 /* 1 = read from SCSI write to Host */
529#define XFERDATAIN_SG 0x0103 /* Transfer data in w/ SG */
530#define XFERDATAOUT_SG 0x0102 /* Transfer data out w/ SG */
531#define XFERDATAIN 0x0101 /* Transfer data in w/o SG */
532#define XFERDATAOUT 0x0100 /* Transfer data out w/o SG */
533
534#define TRM_S1040_DMA_FIFOCNT 0xA1 /* DMA FIFO Counter (R) */
535
536#define TRM_S1040_DMA_CONTROL 0xA1 /* DMA Control (W) */
537#define DMARESETMODULE 0x10 /* Reset PCI/DMA module */
538#define STOPDMAXFER 0x08 /* Stop DMA transfer */
539#define ABORTXFER 0x04 /* Abort DMA transfer */
540#define CLRXFIFO 0x02 /* Clear DMA transfer FIFO */
541#define STARTDMAXFER 0x01 /* Start DMA transfer */
542
543#define TRM_S1040_DMA_FIFOSTAT 0xA2 /* DMA FIFO Status (R) */
544
545#define TRM_S1040_DMA_STATUS 0xA3 /* DMA Interrupt Status (R/W) */
546#define XFERPENDING 0x80 /* Transfer pending */
547#define SCSIBUSY 0x40 /* SCSI busy */
548#define GLOBALINT 0x20 /* DMA_INTEN bit 0-4 set */
549#define FORCEDMACOMP 0x10 /* Force DMA transfer complete */
550#define DMAXFERERROR 0x08 /* DMA transfer error */
551#define DMAXFERABORT 0x04 /* DMA transfer abort */
552#define DMAXFERCOMP 0x02 /* Bus Master XFER Complete status */
553#define SCSICOMP 0x01 /* SCSI complete interrupt */
554
555#define TRM_S1040_DMA_INTEN 0xA4 /* DMA Interrupt Enable (R/W) */
556#define EN_FORCEDMACOMP 0x10 /* Force DMA transfer complete */
557#define EN_DMAXFERERROR 0x08 /* DMA transfer error */
558#define EN_DMAXFERABORT 0x04 /* DMA transfer abort */
559#define EN_DMAXFERCOMP 0x02 /* Bus Master XFER Complete status */
560#define EN_SCSIINTR 0x01 /* Enable SCSI complete interrupt */
561
562#define TRM_S1040_DMA_CONFIG 0xA6 /* DMA Configuration (R/W) */
563#define DMA_ENHANCE 0x8000 /* Enable DMA enhance feature (SG?) */
564#define DMA_PCI_DUAL_ADDR 0x4000 /* */
565#define DMA_CFG_RES 0x2000 /* Always 1 */
566#define DMA_AUTO_CLR_FIFO 0x1000 /* DISable DMA auto clear FIFO */
567#define DMA_MEM_MULTI_READ 0x0800 /* */
568#define DMA_MEM_WRITE_INVAL 0x0400 /* Memory write and invalidate */
569#define DMA_FIFO_CTRL 0x0300 /* Control FIFO operation with DMA */
570#define DMA_FIFO_HALF_HALF 0x0200 /* Keep half filled on both read/write */
571
572#define TRM_S1040_DMA_XCNT 0xA8 /* DMA Transfer Counter (R/W), 24bits */
573#define TRM_S1040_DMA_CXCNT 0xAC /* DMA Current Transfer Counter (R) */
574#define TRM_S1040_DMA_XLOWADDR 0xB0 /* DMA Transfer Physical Low Address */
575#define TRM_S1040_DMA_XHIGHADDR 0xB4 /* DMA Transfer Physical High Address */
576
577/************************************************************************/
578/* */
579/* The general register offset for TRM_S1040 */
580/* */
581/************************************************************************/
582#define TRM_S1040_GEN_CONTROL 0xD4 /* Global Control */
583#define CTRL_LED 0x80 /* Control onboard LED */
584#define EN_EEPROM 0x10 /* Enable EEPROM programming */
585#define DIS_TERM 0x08 /* Disable onboard termination */
586#define AUTOTERM 0x04 /* Enable Auto SCSI terminator */
587#define LOW8TERM 0x02 /* Enable Lower 8 bit SCSI terminator */
588#define UP8TERM 0x01 /* Enable Upper 8 bit SCSI terminator */
589
590#define TRM_S1040_GEN_STATUS 0xD5 /* Global Status */
591#define GTIMEOUT 0x80 /* Global timer reach 0 */
592#define EXT68HIGH 0x40 /* Higher 8 bit connected externally */
593#define INT68HIGH 0x20 /* Higher 8 bit connected internally */
594#define CON5068 0x10 /* External 50/68 pin connected (low) */
595#define CON68 0x08 /* Internal 68 pin connected (low) */
596#define CON50 0x04 /* Internal 50 pin connected (low!) */
597#define WIDESCSI 0x02 /* Wide SCSI card */
598#define STATUS_LOAD_DEFAULT 0x01 /* */
599
600#define TRM_S1040_GEN_NVRAM 0xD6 /* Serial NON-VOLATILE RAM port */
601#define NVR_BITOUT 0x08 /* Serial data out */
602#define NVR_BITIN 0x04 /* Serial data in */
603#define NVR_CLOCK 0x02 /* Serial clock */
604#define NVR_SELECT 0x01 /* Serial select */
605
606#define TRM_S1040_GEN_EDATA 0xD7 /* Parallel EEPROM data port */
607#define TRM_S1040_GEN_EADDRESS 0xD8 /* Parallel EEPROM address */
608#define TRM_S1040_GEN_TIMER 0xDB /* Global timer */
609
610/************************************************************************/
611/* */
612/* NvmTarCfg0: Target configuration byte 0 :..pDCB->DevMode */
613/* */
614/************************************************************************/
615#define NTC_DO_WIDE_NEGO 0x20 /* Wide negotiate */
616#define NTC_DO_TAG_QUEUEING 0x10 /* Enable SCSI tag queuing */
617#define NTC_DO_SEND_START 0x08 /* Send start command SPINUP */
618#define NTC_DO_DISCONNECT 0x04 /* Enable SCSI disconnect */
619#define NTC_DO_SYNC_NEGO 0x02 /* Sync negotiation */
620#define NTC_DO_PARITY_CHK 0x01 /* (it sould define at NAC) */
621 /* Parity check enable */
622
623/************************************************************************/
624/* */
625/* Nvram Initiater bits definition */
626/* */
627/************************************************************************/
628#if 0
629#define MORE2_DRV BIT0
630#define GREATER_1G BIT1
631#define RST_SCSI_BUS BIT2
632#define ACTIVE_NEGATION BIT3
633#define NO_SEEK BIT4
634#define LUN_CHECK BIT5
635#endif
636
637/************************************************************************/
638/* */
639/* Nvram Adapter Cfg bits definition */
640/* */
641/************************************************************************/
642#define NAC_SCANLUN 0x20 /* Include LUN as BIOS device */
643#define NAC_POWERON_SCSI_RESET 0x04 /* Power on reset enable */
644#define NAC_GREATER_1G 0x02 /* > 1G support enable */
645#define NAC_GT2DRIVES 0x01 /* Support more than 2 drives */
646/* #define NAC_DO_PARITY_CHK 0x08 */ /* Parity check enable */
647
648#endif