| /** @file |
| This header file contains all of the PXE type definitions, |
| structure prototypes, global variables and constants that |
| are needed for porting PXE to EFI. |
| |
| Copyright (c) 2006 - 2008, Intel Corporation |
| All rights reserved. This program and the accompanying materials |
| are licensed and made available under the terms and conditions of the BSD License |
| which accompanies this distribution. The full text of the license may be found at |
| http://opensource.org/licenses/bsd-license.php |
| |
| THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, |
| WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. |
| |
| @par Revision Reference: |
| 32/64-bit PXE specification: |
| alpha-4, 99-Dec-17 |
| |
| **/ |
| |
| #ifndef __EFI_PXE_H__ |
| #define __EFI_PXE_H__ |
| |
| #pragma pack(1) |
| |
| #define PXE_BUSTYPE(a, b, c, d) \ |
| ( \ |
| (((PXE_UINT32) (d) & 0xFF) << 24) | (((PXE_UINT32) (c) & 0xFF) << 16) | (((PXE_UINT32) (b) & 0xFF) << 8) | \ |
| ((PXE_UINT32) (a) & 0xFF) \ |
| ) |
| |
| /// |
| /// UNDI ROM ID and devive ID signature |
| /// |
| #define PXE_BUSTYPE_PXE PXE_BUSTYPE ('!', 'P', 'X', 'E') |
| |
| /// |
| /// BUS ROM ID signatures |
| /// |
| #define PXE_BUSTYPE_PCI PXE_BUSTYPE ('P', 'C', 'I', 'R') |
| #define PXE_BUSTYPE_PC_CARD PXE_BUSTYPE ('P', 'C', 'C', 'R') |
| #define PXE_BUSTYPE_USB PXE_BUSTYPE ('U', 'S', 'B', 'R') |
| #define PXE_BUSTYPE_1394 PXE_BUSTYPE ('1', '3', '9', '4') |
| |
| #define PXE_SWAP_UINT16(n) ((((PXE_UINT16) (n) & 0x00FF) << 8) | (((PXE_UINT16) (n) & 0xFF00) >> 8)) |
| |
| #define PXE_SWAP_UINT32(n) \ |
| ((((PXE_UINT32)(n) & 0x000000FF) << 24) | \ |
| (((PXE_UINT32)(n) & 0x0000FF00) << 8) | \ |
| (((PXE_UINT32)(n) & 0x00FF0000) >> 8) | \ |
| (((PXE_UINT32)(n) & 0xFF000000) >> 24)) |
| |
| #define PXE_SWAP_UINT64(n) \ |
| ((((PXE_UINT64)(n) & 0x00000000000000FFULL) << 56) | \ |
| (((PXE_UINT64)(n) & 0x000000000000FF00ULL) << 40) | \ |
| (((PXE_UINT64)(n) & 0x0000000000FF0000ULL) << 24) | \ |
| (((PXE_UINT64)(n) & 0x00000000FF000000ULL) << 8) | \ |
| (((PXE_UINT64)(n) & 0x000000FF00000000ULL) >> 8) | \ |
| (((PXE_UINT64)(n) & 0x0000FF0000000000ULL) >> 24) | \ |
| (((PXE_UINT64)(n) & 0x00FF000000000000ULL) >> 40) | \ |
| (((PXE_UINT64)(n) & 0xFF00000000000000ULL) >> 56)) |
| |
| |
| #define PXE_CPBSIZE_NOT_USED 0 ///< zero |
| #define PXE_DBSIZE_NOT_USED 0 ///< zero |
| #define PXE_CPBADDR_NOT_USED (PXE_UINT64) 0 ///< zero |
| #define PXE_DBADDR_NOT_USED (PXE_UINT64) 0 ///< zero |
| #define PXE_CONST CONST |
| |
| #define PXE_VOLATILE volatile |
| |
| typedef VOID PXE_VOID; |
| typedef UINT8 PXE_UINT8; |
| typedef UINT16 PXE_UINT16; |
| typedef UINT32 PXE_UINT32; |
| typedef UINTN PXE_UINTN; |
| |
| /// |
| /// typedef unsigned long PXE_UINT64; |
| /// |
| typedef UINT64 PXE_UINT64; |
| |
| typedef PXE_UINT8 PXE_BOOL; |
| #define PXE_FALSE 0 ///< zero |
| #define PXE_TRUE (!PXE_FALSE) |
| |
| typedef PXE_UINT16 PXE_OPCODE; |
| |
| /// |
| /// Return UNDI operational state. |
| /// |
| #define PXE_OPCODE_GET_STATE 0x0000 |
| |
| /// |
| /// Change UNDI operational state from Stopped to Started. |
| /// |
| #define PXE_OPCODE_START 0x0001 |
| |
| /// |
| /// Change UNDI operational state from Started to Stopped. |
| /// |
| #define PXE_OPCODE_STOP 0x0002 |
| |
| /// |
| /// Get UNDI initialization information. |
| /// |
| #define PXE_OPCODE_GET_INIT_INFO 0x0003 |
| |
| /// |
| /// Get NIC configuration information. |
| /// |
| #define PXE_OPCODE_GET_CONFIG_INFO 0x0004 |
| |
| /// |
| /// Changed UNDI operational state from Started to Initialized. |
| /// |
| #define PXE_OPCODE_INITIALIZE 0x0005 |
| |
| /// |
| /// Re-initialize the NIC H/W. |
| /// |
| #define PXE_OPCODE_RESET 0x0006 |
| |
| /// |
| /// Change the UNDI operational state from Initialized to Started. |
| /// |
| #define PXE_OPCODE_SHUTDOWN 0x0007 |
| |
| /// |
| /// Read & change state of external interrupt enables. |
| /// |
| #define PXE_OPCODE_INTERRUPT_ENABLES 0x0008 |
| |
| /// |
| /// Read & change state of packet receive filters. |
| /// |
| #define PXE_OPCODE_RECEIVE_FILTERS 0x0009 |
| |
| /// |
| /// Read & change station MAC address. |
| /// |
| #define PXE_OPCODE_STATION_ADDRESS 0x000A |
| |
| /// |
| /// Read traffic statistics. |
| /// |
| #define PXE_OPCODE_STATISTICS 0x000B |
| |
| /// |
| /// Convert multicast IP address to multicast MAC address. |
| /// |
| #define PXE_OPCODE_MCAST_IP_TO_MAC 0x000C |
| |
| /// |
| /// Read or change non-volatile storage on the NIC. |
| /// |
| #define PXE_OPCODE_NVDATA 0x000D |
| |
| /// |
| /// Get & clear interrupt status. |
| /// |
| #define PXE_OPCODE_GET_STATUS 0x000E |
| |
| /// |
| /// Fill media header in packet for transmit. |
| /// |
| #define PXE_OPCODE_FILL_HEADER 0x000F |
| |
| /// |
| /// Transmit packet(s). |
| /// |
| #define PXE_OPCODE_TRANSMIT 0x0010 |
| |
| /// |
| /// Receive packet. |
| /// |
| #define PXE_OPCODE_RECEIVE 0x0011 |
| |
| /// |
| /// Last valid PXE UNDI OpCode number. |
| /// |
| #define PXE_OPCODE_LAST_VALID 0x0011 |
| |
| typedef PXE_UINT16 PXE_OPFLAGS; |
| |
| #define PXE_OPFLAGS_NOT_USED 0x0000 |
| |
| // |
| // ////////////////////////////////////// |
| // UNDI Get State |
| // |
| // No OpFlags |
| |
| //////////////////////////////////////// |
| // UNDI Start |
| // |
| // No OpFlags |
| |
| //////////////////////////////////////// |
| // UNDI Stop |
| // |
| // No OpFlags |
| |
| //////////////////////////////////////// |
| // UNDI Get Init Info |
| // |
| // No Opflags |
| |
| //////////////////////////////////////// |
| // UNDI Get Config Info |
| // |
| // No Opflags |
| |
| /// |
| /// UNDI Initialize |
| /// |
| #define PXE_OPFLAGS_INITIALIZE_CABLE_DETECT_MASK 0x0001 |
| #define PXE_OPFLAGS_INITIALIZE_DETECT_CABLE 0x0000 |
| #define PXE_OPFLAGS_INITIALIZE_DO_NOT_DETECT_CABLE 0x0001 |
| |
| /// |
| /// |
| /// UNDI Reset |
| /// |
| #define PXE_OPFLAGS_RESET_DISABLE_INTERRUPTS 0x0001 |
| #define PXE_OPFLAGS_RESET_DISABLE_FILTERS 0x0002 |
| |
| /// |
| /// UNDI Shutdown |
| /// |
| /// No OpFlags |
| |
| /// |
| /// UNDI Interrupt Enables |
| /// |
| /// |
| /// Select whether to enable or disable external interrupt signals. |
| /// Setting both enable and disable will return PXE_STATCODE_INVALID_OPFLAGS. |
| /// |
| #define PXE_OPFLAGS_INTERRUPT_OPMASK 0xC000 |
| #define PXE_OPFLAGS_INTERRUPT_ENABLE 0x8000 |
| #define PXE_OPFLAGS_INTERRUPT_DISABLE 0x4000 |
| #define PXE_OPFLAGS_INTERRUPT_READ 0x0000 |
| |
| /// |
| /// Enable receive interrupts. An external interrupt will be generated |
| /// after a complete non-error packet has been received. |
| /// |
| #define PXE_OPFLAGS_INTERRUPT_RECEIVE 0x0001 |
| |
| /// |
| /// Enable transmit interrupts. An external interrupt will be generated |
| /// after a complete non-error packet has been transmitted. |
| /// |
| #define PXE_OPFLAGS_INTERRUPT_TRANSMIT 0x0002 |
| |
| /// |
| /// Enable command interrupts. An external interrupt will be generated |
| /// when command execution stops. |
| /// |
| #define PXE_OPFLAGS_INTERRUPT_COMMAND 0x0004 |
| |
| /// |
| /// Generate software interrupt. Setting this bit generates an external |
| /// interrupt, if it is supported by the hardware. |
| /// |
| #define PXE_OPFLAGS_INTERRUPT_SOFTWARE 0x0008 |
| |
| /// |
| /// UNDI Receive Filters |
| /// |
| /// |
| /// Select whether to enable or disable receive filters. |
| /// Setting both enable and disable will return PXE_STATCODE_INVALID_OPCODE. |
| /// |
| #define PXE_OPFLAGS_RECEIVE_FILTER_OPMASK 0xC000 |
| #define PXE_OPFLAGS_RECEIVE_FILTER_ENABLE 0x8000 |
| #define PXE_OPFLAGS_RECEIVE_FILTER_DISABLE 0x4000 |
| #define PXE_OPFLAGS_RECEIVE_FILTER_READ 0x0000 |
| |
| /// |
| /// To reset the contents of the multicast MAC address filter list, |
| /// set this OpFlag: |
| /// |
| #define PXE_OPFLAGS_RECEIVE_FILTER_RESET_MCAST_LIST 0x2000 |
| |
| /// |
| /// Enable unicast packet receiving. Packets sent to the current station |
| /// MAC address will be received. |
| /// |
| #define PXE_OPFLAGS_RECEIVE_FILTER_UNICAST 0x0001 |
| |
| /// |
| /// Enable broadcast packet receiving. Packets sent to the broadcast |
| /// MAC address will be received. |
| /// |
| #define PXE_OPFLAGS_RECEIVE_FILTER_BROADCAST 0x0002 |
| |
| /// |
| /// Enable filtered multicast packet receiving. Packets sent to any |
| /// of the multicast MAC addresses in the multicast MAC address filter |
| /// list will be received. If the filter list is empty, no multicast |
| /// |
| #define PXE_OPFLAGS_RECEIVE_FILTER_FILTERED_MULTICAST 0x0004 |
| |
| /// |
| /// Enable promiscuous packet receiving. All packets will be received. |
| /// |
| #define PXE_OPFLAGS_RECEIVE_FILTER_PROMISCUOUS 0x0008 |
| |
| /// |
| /// Enable promiscuous multicast packet receiving. All multicast |
| /// packets will be received. |
| /// |
| #define PXE_OPFLAGS_RECEIVE_FILTER_ALL_MULTICAST 0x0010 |
| |
| /// |
| /// UNDI Station Address |
| /// |
| #define PXE_OPFLAGS_STATION_ADDRESS_READ 0x0000 |
| #define PXE_OPFLAGS_STATION_ADDRESS_WRITE 0x0000 |
| #define PXE_OPFLAGS_STATION_ADDRESS_RESET 0x0001 |
| |
| /// |
| /// UNDI Statistics |
| /// |
| #define PXE_OPFLAGS_STATISTICS_READ 0x0000 |
| #define PXE_OPFLAGS_STATISTICS_RESET 0x0001 |
| |
| /// |
| /// UNDI MCast IP to MAC |
| /// |
| /// |
| /// Identify the type of IP address in the CPB. |
| /// |
| #define PXE_OPFLAGS_MCAST_IP_TO_MAC_OPMASK 0x0003 |
| #define PXE_OPFLAGS_MCAST_IPV4_TO_MAC 0x0000 |
| #define PXE_OPFLAGS_MCAST_IPV6_TO_MAC 0x0001 |
| |
| /// |
| /// UNDI NvData |
| /// |
| /// |
| /// Select the type of non-volatile data operation. |
| /// |
| #define PXE_OPFLAGS_NVDATA_OPMASK 0x0001 |
| #define PXE_OPFLAGS_NVDATA_READ 0x0000 |
| #define PXE_OPFLAGS_NVDATA_WRITE 0x0001 |
| |
| /// |
| /// UNDI Get Status |
| /// |
| /// |
| /// Return current interrupt status. This will also clear any interrupts |
| /// that are currently set. This can be used in a polling routine. The |
| /// interrupt flags are still set and cleared even when the interrupts |
| /// are disabled. |
| /// |
| #define PXE_OPFLAGS_GET_INTERRUPT_STATUS 0x0001 |
| |
| /// |
| /// Return list of transmitted buffers for recycling. Transmit buffers |
| /// must not be changed or unallocated until they have recycled. After |
| /// issuing a transmit command, wait for a transmit complete interrupt. |
| /// When a transmit complete interrupt is received, read the transmitted |
| /// buffers. Do not plan on getting one buffer per interrupt. Some |
| /// NICs and UNDIs may transmit multiple buffers per interrupt. |
| /// |
| #define PXE_OPFLAGS_GET_TRANSMITTED_BUFFERS 0x0002 |
| |
| /// |
| /// UNDI Fill Header |
| /// |
| #define PXE_OPFLAGS_FILL_HEADER_OPMASK 0x0001 |
| #define PXE_OPFLAGS_FILL_HEADER_FRAGMENTED 0x0001 |
| #define PXE_OPFLAGS_FILL_HEADER_WHOLE 0x0000 |
| |
| /// |
| /// UNDI Transmit |
| /// |
| /// |
| /// S/W UNDI only. Return after the packet has been transmitted. A |
| /// transmit complete interrupt will still be generated and the transmit |
| /// buffer will have to be recycled. |
| /// |
| #define PXE_OPFLAGS_SWUNDI_TRANSMIT_OPMASK 0x0001 |
| #define PXE_OPFLAGS_TRANSMIT_BLOCK 0x0001 |
| #define PXE_OPFLAGS_TRANSMIT_DONT_BLOCK 0x0000 |
| |
| #define PXE_OPFLAGS_TRANSMIT_OPMASK 0x0002 |
| #define PXE_OPFLAGS_TRANSMIT_FRAGMENTED 0x0002 |
| #define PXE_OPFLAGS_TRANSMIT_WHOLE 0x0000 |
| |
| /// |
| /// UNDI Receive |
| /// |
| /// No OpFlags |
| /// |
| |
| /// |
| /// PXE STATFLAGS |
| /// |
| typedef PXE_UINT16 PXE_STATFLAGS; |
| |
| #define PXE_STATFLAGS_INITIALIZE 0x0000 |
| |
| /// |
| /// Common StatFlags that can be returned by all commands. |
| /// |
| /// |
| /// The COMMAND_COMPLETE and COMMAND_FAILED status flags must be |
| /// implemented by all UNDIs. COMMAND_QUEUED is only needed by UNDIs |
| /// that support command queuing. |
| /// |
| #define PXE_STATFLAGS_STATUS_MASK 0xC000 |
| #define PXE_STATFLAGS_COMMAND_COMPLETE 0xC000 |
| #define PXE_STATFLAGS_COMMAND_FAILED 0x8000 |
| #define PXE_STATFLAGS_COMMAND_QUEUED 0x4000 |
| |
| /// |
| /// UNDI Get State |
| /// |
| #define PXE_STATFLAGS_GET_STATE_MASK 0x0003 |
| #define PXE_STATFLAGS_GET_STATE_INITIALIZED 0x0002 |
| #define PXE_STATFLAGS_GET_STATE_STARTED 0x0001 |
| #define PXE_STATFLAGS_GET_STATE_STOPPED 0x0000 |
| |
| /// |
| /// UNDI Start |
| /// |
| /// No additional StatFlags |
| /// |
| |
| /// |
| /// UNDI Get Init Info |
| /// |
| #define PXE_STATFLAGS_CABLE_DETECT_MASK 0x0001 |
| #define PXE_STATFLAGS_CABLE_DETECT_NOT_SUPPORTED 0x0000 |
| #define PXE_STATFLAGS_CABLE_DETECT_SUPPORTED 0x0001 |
| |
| /// |
| /// UNDI Initialize |
| /// |
| #define PXE_STATFLAGS_INITIALIZED_NO_MEDIA 0x0001 |
| |
| /// |
| /// UNDI Reset |
| /// |
| #define PXE_STATFLAGS_RESET_NO_MEDIA 0x0001 |
| |
| /// |
| /// UNDI Shutdown |
| /// |
| /// No additional StatFlags |
| |
| /// |
| /// UNDI Interrupt Enables |
| /// |
| /// |
| /// If set, receive interrupts are enabled. |
| /// |
| #define PXE_STATFLAGS_INTERRUPT_RECEIVE 0x0001 |
| |
| /// |
| /// If set, transmit interrupts are enabled. |
| /// |
| #define PXE_STATFLAGS_INTERRUPT_TRANSMIT 0x0002 |
| |
| /// |
| /// If set, command interrupts are enabled. |
| /// |
| #define PXE_STATFLAGS_INTERRUPT_COMMAND 0x0004 |
| |
| /// |
| /// UNDI Receive Filters |
| /// |
| |
| /// |
| /// If set, unicast packets will be received. |
| /// |
| #define PXE_STATFLAGS_RECEIVE_FILTER_UNICAST 0x0001 |
| |
| /// |
| /// If set, broadcast packets will be received. |
| /// |
| #define PXE_STATFLAGS_RECEIVE_FILTER_BROADCAST 0x0002 |
| |
| /// |
| /// If set, multicast packets that match up with the multicast address |
| /// filter list will be received. |
| /// |
| #define PXE_STATFLAGS_RECEIVE_FILTER_FILTERED_MULTICAST 0x0004 |
| |
| /// |
| /// If set, all packets will be received. |
| /// |
| #define PXE_STATFLAGS_RECEIVE_FILTER_PROMISCUOUS 0x0008 |
| |
| /// |
| /// If set, all multicast packets will be received. |
| /// |
| #define PXE_STATFLAGS_RECEIVE_FILTER_ALL_MULTICAST 0x0010 |
| |
| /// |
| /// UNDI Station Address |
| /// |
| /// No additional StatFlags |
| /// |
| |
| /// |
| /// UNDI Statistics |
| /// |
| /// No additional StatFlags |
| /// |
| |
| /// |
| //// UNDI MCast IP to MAC |
| //// |
| //// No additional StatFlags |
| |
| /// |
| /// UNDI NvData |
| /// |
| /// No additional StatFlags |
| /// |
| |
| /// |
| /// UNDI Get Status |
| /// |
| |
| /// |
| /// Use to determine if an interrupt has occurred. |
| /// |
| #define PXE_STATFLAGS_GET_STATUS_INTERRUPT_MASK 0x000F |
| #define PXE_STATFLAGS_GET_STATUS_NO_INTERRUPTS 0x0000 |
| |
| /// |
| /// If set, at least one receive interrupt occurred. |
| /// |
| #define PXE_STATFLAGS_GET_STATUS_RECEIVE 0x0001 |
| |
| /// |
| /// If set, at least one transmit interrupt occurred. |
| /// |
| #define PXE_STATFLAGS_GET_STATUS_TRANSMIT 0x0002 |
| |
| /// |
| /// If set, at least one command interrupt occurred. |
| /// |
| #define PXE_STATFLAGS_GET_STATUS_COMMAND 0x0004 |
| |
| /// |
| /// If set, at least one software interrupt occurred. |
| /// |
| #define PXE_STATFLAGS_GET_STATUS_SOFTWARE 0x0008 |
| |
| /// |
| /// This flag is set if the transmitted buffer queue is empty. This flag |
| /// will be set if all transmitted buffer addresses get written into the DB. |
| /// |
| #define PXE_STATFLAGS_GET_STATUS_TXBUF_QUEUE_EMPTY 0x0010 |
| |
| /// |
| /// This flag is set if no transmitted buffer addresses were written |
| /// into the DB. (This could be because DBsize was too small.) |
| /// |
| #define PXE_STATFLAGS_GET_STATUS_NO_TXBUFS_WRITTEN 0x0020 |
| |
| /// |
| /// UNDI Fill Header |
| /// |
| /// No additional StatFlags |
| /// |
| |
| /// |
| /// UNDI Transmit |
| /// |
| /// No additional StatFlags. |
| |
| /// |
| /// UNDI Receive |
| /// |
| |
| /// |
| /// No additional StatFlags. |
| /// |
| typedef PXE_UINT16 PXE_STATCODE; |
| |
| #define PXE_STATCODE_INITIALIZE 0x0000 |
| |
| /// |
| /// Common StatCodes returned by all UNDI commands, UNDI protocol functions |
| /// and BC protocol functions. |
| /// |
| #define PXE_STATCODE_SUCCESS 0x0000 |
| |
| #define PXE_STATCODE_INVALID_CDB 0x0001 |
| #define PXE_STATCODE_INVALID_CPB 0x0002 |
| #define PXE_STATCODE_BUSY 0x0003 |
| #define PXE_STATCODE_QUEUE_FULL 0x0004 |
| #define PXE_STATCODE_ALREADY_STARTED 0x0005 |
| #define PXE_STATCODE_NOT_STARTED 0x0006 |
| #define PXE_STATCODE_NOT_SHUTDOWN 0x0007 |
| #define PXE_STATCODE_ALREADY_INITIALIZED 0x0008 |
| #define PXE_STATCODE_NOT_INITIALIZED 0x0009 |
| #define PXE_STATCODE_DEVICE_FAILURE 0x000A |
| #define PXE_STATCODE_NVDATA_FAILURE 0x000B |
| #define PXE_STATCODE_UNSUPPORTED 0x000C |
| #define PXE_STATCODE_BUFFER_FULL 0x000D |
| #define PXE_STATCODE_INVALID_PARAMETER 0x000E |
| #define PXE_STATCODE_INVALID_UNDI 0x000F |
| #define PXE_STATCODE_IPV4_NOT_SUPPORTED 0x0010 |
| #define PXE_STATCODE_IPV6_NOT_SUPPORTED 0x0011 |
| #define PXE_STATCODE_NOT_ENOUGH_MEMORY 0x0012 |
| #define PXE_STATCODE_NO_DATA 0x0013 |
| |
| typedef PXE_UINT16 PXE_IFNUM; |
| |
| /// |
| /// This interface number must be passed to the S/W UNDI Start command. |
| /// |
| #define PXE_IFNUM_START 0x0000 |
| |
| /// |
| /// This interface number is returned by the S/W UNDI Get State and |
| /// Start commands if information in the CDB, CPB or DB is invalid. |
| /// |
| #define PXE_IFNUM_INVALID 0x0000 |
| |
| typedef PXE_UINT16 PXE_CONTROL; |
| |
| /// |
| /// Setting this flag directs the UNDI to queue this command for later |
| /// execution if the UNDI is busy and it supports command queuing. |
| /// If queuing is not supported, a PXE_STATCODE_INVALID_CONTROL error |
| /// is returned. If the queue is full, a PXE_STATCODE_CDB_QUEUE_FULL |
| /// error is returned. |
| /// |
| #define PXE_CONTROL_QUEUE_IF_BUSY 0x0002 |
| |
| /// |
| /// These two bit values are used to determine if there are more UNDI |
| /// CDB structures following this one. If the link bit is set, there |
| /// must be a CDB structure following this one. Execution will start |
| /// on the next CDB structure as soon as this one completes successfully. |
| /// If an error is generated by this command, execution will stop. |
| /// |
| #define PXE_CONTROL_LINK 0x0001 |
| #define PXE_CONTROL_LAST_CDB_IN_LIST 0x0000 |
| |
| typedef PXE_UINT8 PXE_FRAME_TYPE; |
| |
| #define PXE_FRAME_TYPE_NONE 0x00 |
| #define PXE_FRAME_TYPE_UNICAST 0x01 |
| #define PXE_FRAME_TYPE_BROADCAST 0x02 |
| #define PXE_FRAME_TYPE_FILTERED_MULTICAST 0x03 |
| #define PXE_FRAME_TYPE_PROMISCUOUS 0x04 |
| #define PXE_FRAME_TYPE_PROMISCUOUS_MULTICAST 0x05 |
| |
| #define PXE_FRAME_TYPE_MULTICAST PXE_FRAME_TYPE_FILTERED_MULTICAST |
| |
| typedef PXE_UINT32 PXE_IPV4; |
| |
| typedef PXE_UINT32 PXE_IPV6[4]; |
| #define PXE_MAC_LENGTH 32 |
| |
| typedef PXE_UINT8 PXE_MAC_ADDR[PXE_MAC_LENGTH]; |
| |
| typedef PXE_UINT8 PXE_IFTYPE; |
| typedef UINT16 PXE_MEDIA_PROTOCOL; |
| |
| /// |
| /// This information is from the ARP section of RFC 1700. |
| /// |
| /// 1 Ethernet (10Mb) [JBP] |
| /// 2 Experimental Ethernet (3Mb) [JBP] |
| /// 3 Amateur Radio AX.25 [PXK] |
| /// 4 Proteon ProNET Token Ring [JBP] |
| /// 5 Chaos [GXP] |
| /// 6 IEEE 802 Networks [JBP] |
| /// 7 ARCNET [JBP] |
| /// 8 Hyperchannel [JBP] |
| /// 9 Lanstar [TU] |
| /// 10 Autonet Short Address [MXB1] |
| /// 11 LocalTalk [JKR1] |
| /// 12 LocalNet (IBM* PCNet or SYTEK* LocalNET) [JXM] |
| /// 13 Ultra link [RXD2] |
| /// 14 SMDS [GXC1] |
| /// 15 Frame Relay [AGM] |
| /// 16 Asynchronous Transmission Mode (ATM) [JXB2] |
| /// 17 HDLC [JBP] |
| /// 18 Fibre Channel [Yakov Rekhter] |
| /// 19 Asynchronous Transmission Mode (ATM) [Mark Laubach] |
| /// 20 Serial Line [JBP] |
| /// 21 Asynchronous Transmission Mode (ATM) [MXB1] |
| /// |
| /// * Other names and brands may be claimed as the property of others. |
| /// |
| #define PXE_IFTYPE_ETHERNET 0x01 |
| #define PXE_IFTYPE_TOKENRING 0x04 |
| #define PXE_IFTYPE_FIBRE_CHANNEL 0x12 |
| |
| typedef struct s_pxe_hw_undi { |
| PXE_UINT32 Signature; ///< PXE_ROMID_SIGNATURE |
| PXE_UINT8 Len; ///< sizeof(PXE_HW_UNDI) |
| PXE_UINT8 Fudge; ///< makes 8-bit cksum equal zero |
| PXE_UINT8 Rev; ///< PXE_ROMID_REV |
| PXE_UINT8 IFcnt; ///< physical connector count |
| PXE_UINT8 MajorVer; ///< PXE_ROMID_MAJORVER |
| PXE_UINT8 MinorVer; ///< PXE_ROMID_MINORVER |
| PXE_UINT16 reserved; ///< zero, not used |
| PXE_UINT32 Implementation; ///< implementation flags |
| ///< reserved ///< vendor use |
| ///< UINT32 Status; ///< status port |
| ///< UINT32 Command; ///< command port |
| ///< UINT64 CDBaddr; ///< CDB address port |
| ///< |
| } PXE_HW_UNDI; |
| |
| /// |
| /// Status port bit definitions |
| /// |
| |
| /// |
| /// UNDI operation state |
| /// |
| #define PXE_HWSTAT_STATE_MASK 0xC0000000 |
| #define PXE_HWSTAT_BUSY 0xC0000000 |
| #define PXE_HWSTAT_INITIALIZED 0x80000000 |
| #define PXE_HWSTAT_STARTED 0x40000000 |
| #define PXE_HWSTAT_STOPPED 0x00000000 |
| |
| /// |
| /// If set, last command failed |
| /// |
| #define PXE_HWSTAT_COMMAND_FAILED 0x20000000 |
| |
| /// |
| /// If set, identifies enabled receive filters |
| /// |
| #define PXE_HWSTAT_PROMISCUOUS_MULTICAST_RX_ENABLED 0x00001000 |
| #define PXE_HWSTAT_PROMISCUOUS_RX_ENABLED 0x00000800 |
| #define PXE_HWSTAT_BROADCAST_RX_ENABLED 0x00000400 |
| #define PXE_HWSTAT_MULTICAST_RX_ENABLED 0x00000200 |
| #define PXE_HWSTAT_UNICAST_RX_ENABLED 0x00000100 |
| |
| /// |
| /// If set, identifies enabled external interrupts |
| /// |
| #define PXE_HWSTAT_SOFTWARE_INT_ENABLED 0x00000080 |
| #define PXE_HWSTAT_TX_COMPLETE_INT_ENABLED 0x00000040 |
| #define PXE_HWSTAT_PACKET_RX_INT_ENABLED 0x00000020 |
| #define PXE_HWSTAT_CMD_COMPLETE_INT_ENABLED 0x00000010 |
| |
| /// |
| /// If set, identifies pending interrupts |
| /// |
| #define PXE_HWSTAT_SOFTWARE_INT_PENDING 0x00000008 |
| #define PXE_HWSTAT_TX_COMPLETE_INT_PENDING 0x00000004 |
| #define PXE_HWSTAT_PACKET_RX_INT_PENDING 0x00000002 |
| #define PXE_HWSTAT_CMD_COMPLETE_INT_PENDING 0x00000001 |
| |
| /// |
| /// Command port definitions |
| /// |
| |
| /// |
| /// If set, CDB identified in CDBaddr port is given to UNDI. |
| /// If not set, other bits in this word will be processed. |
| /// |
| #define PXE_HWCMD_ISSUE_COMMAND 0x80000000 |
| #define PXE_HWCMD_INTS_AND_FILTS 0x00000000 |
| |
| /// |
| /// Use these to enable/disable receive filters. |
| /// |
| #define PXE_HWCMD_PROMISCUOUS_MULTICAST_RX_ENABLE 0x00001000 |
| #define PXE_HWCMD_PROMISCUOUS_RX_ENABLE 0x00000800 |
| #define PXE_HWCMD_BROADCAST_RX_ENABLE 0x00000400 |
| #define PXE_HWCMD_MULTICAST_RX_ENABLE 0x00000200 |
| #define PXE_HWCMD_UNICAST_RX_ENABLE 0x00000100 |
| |
| /// |
| /// Use these to enable/disable external interrupts |
| /// |
| #define PXE_HWCMD_SOFTWARE_INT_ENABLE 0x00000080 |
| #define PXE_HWCMD_TX_COMPLETE_INT_ENABLE 0x00000040 |
| #define PXE_HWCMD_PACKET_RX_INT_ENABLE 0x00000020 |
| #define PXE_HWCMD_CMD_COMPLETE_INT_ENABLE 0x00000010 |
| |
| /// |
| /// Use these to clear pending external interrupts |
| /// |
| #define PXE_HWCMD_CLEAR_SOFTWARE_INT 0x00000008 |
| #define PXE_HWCMD_CLEAR_TX_COMPLETE_INT 0x00000004 |
| #define PXE_HWCMD_CLEAR_PACKET_RX_INT 0x00000002 |
| #define PXE_HWCMD_CLEAR_CMD_COMPLETE_INT 0x00000001 |
| |
| typedef struct s_pxe_sw_undi { |
| PXE_UINT32 Signature; ///< PXE_ROMID_SIGNATURE |
| PXE_UINT8 Len; ///< sizeof(PXE_SW_UNDI) |
| PXE_UINT8 Fudge; ///< makes 8-bit cksum zero |
| PXE_UINT8 Rev; ///< PXE_ROMID_REV |
| PXE_UINT8 IFcnt; ///< physical connector count |
| PXE_UINT8 MajorVer; ///< PXE_ROMID_MAJORVER |
| PXE_UINT8 MinorVer; ///< PXE_ROMID_MINORVER |
| PXE_UINT16 reserved1; ///< zero, not used |
| PXE_UINT32 Implementation; ///< Implementation flags |
| PXE_UINT64 EntryPoint; ///< API entry point |
| PXE_UINT8 reserved2[3]; ///< zero, not used |
| PXE_UINT8 BusCnt; ///< number of bustypes supported |
| PXE_UINT32 BusType[1]; ///< list of supported bustypes |
| } PXE_SW_UNDI; |
| |
| typedef union u_pxe_undi { |
| PXE_HW_UNDI hw; |
| PXE_SW_UNDI sw; |
| } PXE_UNDI; |
| |
| /// |
| /// Signature of !PXE structure |
| /// |
| #define PXE_ROMID_SIGNATURE PXE_BUSTYPE ('!', 'P', 'X', 'E') |
| |
| /// |
| /// !PXE structure format revision |
| /// |
| #define PXE_ROMID_REV 0x02 |
| |
| /// |
| /// UNDI command interface revision. These are the values that get sent |
| /// in option 94 (Client Network Interface Identifier) in the DHCP Discover |
| /// and PXE Boot Server Request packets. |
| /// |
| #define PXE_ROMID_MAJORVER 0x03 |
| #define PXE_ROMID_MINORVER 0x01 |
| |
| /// |
| /// Implementation flags |
| /// |
| #define PXE_ROMID_IMP_HW_UNDI 0x80000000 |
| #define PXE_ROMID_IMP_SW_VIRT_ADDR 0x40000000 |
| #define PXE_ROMID_IMP_64BIT_DEVICE 0x00010000 |
| #define PXE_ROMID_IMP_FRAG_SUPPORTED 0x00008000 |
| #define PXE_ROMID_IMP_CMD_LINK_SUPPORTED 0x00004000 |
| #define PXE_ROMID_IMP_CMD_QUEUE_SUPPORTED 0x00002000 |
| #define PXE_ROMID_IMP_MULTI_FRAME_SUPPORTED 0x00001000 |
| #define PXE_ROMID_IMP_NVDATA_SUPPORT_MASK 0x00000C00 |
| #define PXE_ROMID_IMP_NVDATA_BULK_WRITABLE 0x00000C00 |
| #define PXE_ROMID_IMP_NVDATA_SPARSE_WRITABLE 0x00000800 |
| #define PXE_ROMID_IMP_NVDATA_READ_ONLY 0x00000400 |
| #define PXE_ROMID_IMP_NVDATA_NOT_AVAILABLE 0x00000000 |
| #define PXE_ROMID_IMP_STATISTICS_SUPPORTED 0x00000200 |
| #define PXE_ROMID_IMP_STATION_ADDR_SETTABLE 0x00000100 |
| #define PXE_ROMID_IMP_PROMISCUOUS_MULTICAST_RX_SUPPORTED 0x00000080 |
| #define PXE_ROMID_IMP_PROMISCUOUS_RX_SUPPORTED 0x00000040 |
| #define PXE_ROMID_IMP_BROADCAST_RX_SUPPORTED 0x00000020 |
| #define PXE_ROMID_IMP_FILTERED_MULTICAST_RX_SUPPORTED 0x00000010 |
| #define PXE_ROMID_IMP_SOFTWARE_INT_SUPPORTED 0x00000008 |
| #define PXE_ROMID_IMP_TX_COMPLETE_INT_SUPPORTED 0x00000004 |
| #define PXE_ROMID_IMP_PACKET_RX_INT_SUPPORTED 0x00000002 |
| #define PXE_ROMID_IMP_CMD_COMPLETE_INT_SUPPORTED 0x00000001 |
| |
| typedef struct s_pxe_cdb { |
| PXE_OPCODE OpCode; |
| PXE_OPFLAGS OpFlags; |
| PXE_UINT16 CPBsize; |
| PXE_UINT16 DBsize; |
| PXE_UINT64 CPBaddr; |
| PXE_UINT64 DBaddr; |
| PXE_STATCODE StatCode; |
| PXE_STATFLAGS StatFlags; |
| PXE_UINT16 IFnum; |
| PXE_CONTROL Control; |
| } PXE_CDB; |
| |
| typedef union u_pxe_ip_addr { |
| PXE_IPV6 IPv6; |
| PXE_IPV4 IPv4; |
| } PXE_IP_ADDR; |
| |
| typedef union pxe_device { |
| /// |
| /// PCI and PC Card NICs are both identified using bus, device |
| /// and function numbers. For PC Card, this may require PC |
| /// Card services to be loaded in the BIOS or preboot |
| /// environment. |
| /// |
| struct { |
| /// |
| /// See S/W UNDI ROMID structure definition for PCI and |
| /// PCC BusType definitions. |
| /// |
| PXE_UINT32 BusType; |
| |
| /// |
| /// Bus, device & function numbers that locate this device. |
| /// |
| PXE_UINT16 Bus; |
| PXE_UINT8 Device; |
| PXE_UINT8 Function; |
| } |
| PCI, PCC; |
| |
| } PXE_DEVICE; |
| |
| /// |
| /// cpb and db definitions |
| /// |
| #define MAX_PCI_CONFIG_LEN 64 ///< # of dwords |
| #define MAX_EEPROM_LEN 128 ///< # of dwords |
| #define MAX_XMIT_BUFFERS 32 ///< recycling Q length for xmit_done |
| #define MAX_MCAST_ADDRESS_CNT 8 |
| |
| typedef struct s_pxe_cpb_start_30 { |
| /// |
| /// PXE_VOID Delay(UINTN microseconds); |
| /// |
| /// UNDI will never request a delay smaller than 10 microseconds |
| /// and will always request delays in increments of 10 microseconds. |
| /// The Delay() CallBack routine must delay between n and n + 10 |
| /// microseconds before returning control to the UNDI. |
| /// |
| /// This field cannot be set to zero. |
| /// |
| UINT64 Delay; |
| |
| /// |
| /// PXE_VOID Block(UINT32 enable); |
| /// |
| /// UNDI may need to block multi-threaded/multi-processor access to |
| /// critical code sections when programming or accessing the network |
| /// device. To this end, a blocking service is needed by the UNDI. |
| /// When UNDI needs a block, it will call Block() passing a non-zero |
| /// value. When UNDI no longer needs a block, it will call Block() |
| /// with a zero value. When called, if the Block() is already enabled, |
| /// do not return control to the UNDI until the previous Block() is |
| /// disabled. |
| /// |
| /// This field cannot be set to zero. |
| /// |
| UINT64 Block; |
| |
| /// |
| /// PXE_VOID Virt2Phys(UINT64 virtual, UINT64 physical_ptr); |
| /// |
| /// UNDI will pass the virtual address of a buffer and the virtual |
| /// address of a 64-bit physical buffer. Convert the virtual address |
| /// to a physical address and write the result to the physical address |
| /// buffer. If virtual and physical addresses are the same, just |
| /// copy the virtual address to the physical address buffer. |
| /// |
| /// This field can be set to zero if virtual and physical addresses |
| /// are equal. |
| /// |
| UINT64 Virt2Phys; |
| /// |
| /// PXE_VOID Mem_IO(UINT8 read_write, UINT8 len, UINT64 port, |
| /// UINT64 buf_addr); |
| /// |
| /// UNDI will read or write the device io space using this call back |
| /// function. It passes the number of bytes as the len parameter and it |
| /// will be either 1,2,4 or 8. |
| /// |
| /// This field can not be set to zero. |
| /// |
| UINT64 Mem_IO; |
| } PXE_CPB_START_30; |
| |
| typedef struct s_pxe_cpb_start_31 { |
| /// |
| /// PXE_VOID Delay(UINT64 UnqId, UINTN microseconds); |
| /// |
| /// UNDI will never request a delay smaller than 10 microseconds |
| /// and will always request delays in increments of 10 microseconds. |
| /// The Delay() CallBack routine must delay between n and n + 10 |
| /// microseconds before returning control to the UNDI. |
| /// |
| /// This field cannot be set to zero. |
| /// |
| UINT64 Delay; |
| |
| /// |
| /// PXE_VOID Block(UINT64 unq_id, UINT32 enable); |
| /// |
| /// UNDI may need to block multi-threaded/multi-processor access to |
| /// critical code sections when programming or accessing the network |
| /// device. To this end, a blocking service is needed by the UNDI. |
| /// When UNDI needs a block, it will call Block() passing a non-zero |
| /// value. When UNDI no longer needs a block, it will call Block() |
| /// with a zero value. When called, if the Block() is already enabled, |
| /// do not return control to the UNDI until the previous Block() is |
| /// disabled. |
| /// |
| /// This field cannot be set to zero. |
| /// |
| UINT64 Block; |
| |
| /// |
| /// PXE_VOID Virt2Phys(UINT64 UnqId, UINT64 virtual, UINT64 physical_ptr); |
| /// |
| /// UNDI will pass the virtual address of a buffer and the virtual |
| /// address of a 64-bit physical buffer. Convert the virtual address |
| /// to a physical address and write the result to the physical address |
| /// buffer. If virtual and physical addresses are the same, just |
| /// copy the virtual address to the physical address buffer. |
| /// |
| /// This field can be set to zero if virtual and physical addresses |
| /// are equal. |
| /// |
| UINT64 Virt2Phys; |
| /// |
| /// PXE_VOID Mem_IO(UINT64 UnqId, UINT8 read_write, UINT8 len, UINT64 port, |
| /// UINT64 buf_addr); |
| /// |
| /// UNDI will read or write the device io space using this call back |
| /// function. It passes the number of bytes as the len parameter and it |
| /// will be either 1,2,4 or 8. |
| /// |
| /// This field can not be set to zero. |
| /// |
| UINT64 Mem_IO; |
| /// |
| /// PXE_VOID Map_Mem(UINT64 unq_id, UINT64 virtual_addr, UINT32 size, |
| /// UINT32 Direction, UINT64 mapped_addr); |
| /// |
| /// UNDI will pass the virtual address of a buffer, direction of the data |
| /// flow from/to the mapped buffer (the constants are defined below) |
| /// and a place holder (pointer) for the mapped address. |
| /// This call will Map the given address to a physical DMA address and write |
| /// the result to the mapped_addr pointer. If there is no need to |
| /// map the given address to a lower address (i.e. the given address is |
| /// associated with a physical address that is already compatible to be |
| /// used with the DMA, it converts the given virtual address to it's |
| /// physical address and write that in the mapped address pointer. |
| /// |
| /// This field can be set to zero if there is no mapping service available |
| /// |
| UINT64 Map_Mem; |
| |
| /// |
| /// PXE_VOID UnMap_Mem(UINT64 unq_id, UINT64 virtual_addr, UINT32 size, |
| /// UINT32 Direction, UINT64 mapped_addr); |
| /// |
| /// UNDI will pass the virtual and mapped addresses of a buffer |
| /// This call will un map the given address |
| /// |
| /// This field can be set to zero if there is no unmapping service available |
| /// |
| UINT64 UnMap_Mem; |
| |
| /// |
| /// PXE_VOID Sync_Mem(UINT64 unq_id, UINT64 virtual, |
| /// UINT32 size, UINT32 Direction, UINT64 mapped_addr); |
| /// |
| /// UNDI will pass the virtual and mapped addresses of a buffer |
| /// This call will synchronize the contents of both the virtual and mapped |
| /// buffers for the given Direction. |
| /// |
| /// This field can be set to zero if there is no service available |
| /// |
| UINT64 Sync_Mem; |
| |
| /// |
| /// protocol driver can provide anything for this Unique_ID, UNDI remembers |
| /// that as just a 64bit value assocaited to the interface specified by |
| /// the ifnum and gives it back as a parameter to all the call-back routines |
| /// when calling for that interface! |
| /// |
| UINT64 Unique_ID; |
| } PXE_CPB_START_31; |
| |
| #define TO_AND_FROM_DEVICE 0 |
| #define FROM_DEVICE 1 |
| #define TO_DEVICE 2 |
| |
| #define PXE_DELAY_MILLISECOND 1000 |
| #define PXE_DELAY_SECOND 1000000 |
| #define PXE_IO_READ 0 |
| #define PXE_IO_WRITE 1 |
| #define PXE_MEM_READ 2 |
| #define PXE_MEM_WRITE 4 |
| |
| typedef struct s_pxe_db_get_init_info { |
| /// |
| /// Minimum length of locked memory buffer that must be given to |
| /// the Initialize command. Giving UNDI more memory will generally |
| /// give better performance. |
| /// |
| /// If MemoryRequired is zero, the UNDI does not need and will not |
| /// use system memory to receive and transmit packets. |
| /// |
| PXE_UINT32 MemoryRequired; |
| |
| /// |
| /// Maximum frame data length for Tx/Rx excluding the media header. |
| /// |
| PXE_UINT32 FrameDataLen; |
| |
| /// |
| /// Supported link speeds are in units of mega bits. Common ethernet |
| /// values are 10, 100 and 1000. Unused LinkSpeeds[] entries are zero |
| /// filled. |
| /// |
| PXE_UINT32 LinkSpeeds[4]; |
| |
| /// |
| /// Number of non-volatile storage items. |
| /// |
| PXE_UINT32 NvCount; |
| |
| /// |
| /// Width of non-volatile storage item in bytes. 0, 1, 2 or 4 |
| /// |
| PXE_UINT16 NvWidth; |
| |
| /// |
| /// Media header length. This is the typical media header length for |
| /// this UNDI. This information is needed when allocating receive |
| /// and transmit buffers. |
| /// |
| PXE_UINT16 MediaHeaderLen; |
| |
| /// |
| /// Number of bytes in the NIC hardware (MAC) address. |
| /// |
| PXE_UINT16 HWaddrLen; |
| |
| /// |
| /// Maximum number of multicast MAC addresses in the multicast |
| /// MAC address filter list. |
| /// |
| PXE_UINT16 MCastFilterCnt; |
| |
| /// |
| /// Default number and size of transmit and receive buffers that will |
| /// be allocated by the UNDI. If MemoryRequired is non-zero, this |
| /// allocation will come out of the memory buffer given to the Initialize |
| /// command. If MemoryRequired is zero, this allocation will come out of |
| /// memory on the NIC. |
| /// |
| PXE_UINT16 TxBufCnt; |
| PXE_UINT16 TxBufSize; |
| PXE_UINT16 RxBufCnt; |
| PXE_UINT16 RxBufSize; |
| |
| /// |
| /// Hardware interface types defined in the Assigned Numbers RFC |
| /// and used in DHCP and ARP packets. |
| /// See the PXE_IFTYPE typedef and PXE_IFTYPE_xxx macros. |
| /// |
| PXE_UINT8 IFtype; |
| |
| /// |
| /// Supported duplex. See PXE_DUPLEX_xxxxx #defines below. |
| /// |
| PXE_UINT8 SupportedDuplexModes; |
| |
| /// |
| /// Supported loopback options. See PXE_LOOPBACK_xxxxx #defines below. |
| /// |
| PXE_UINT8 SupportedLoopBackModes; |
| } PXE_DB_GET_INIT_INFO; |
| |
| #define PXE_MAX_TXRX_UNIT_ETHER 1500 |
| |
| #define PXE_HWADDR_LEN_ETHER 0x0006 |
| #define PXE_MAC_HEADER_LEN_ETHER 0x000E |
| |
| #define PXE_DUPLEX_ENABLE_FULL_SUPPORTED 1 |
| #define PXE_DUPLEX_FORCE_FULL_SUPPORTED 2 |
| |
| #define PXE_LOOPBACK_INTERNAL_SUPPORTED 1 |
| #define PXE_LOOPBACK_EXTERNAL_SUPPORTED 2 |
| |
| typedef struct s_pxe_pci_config_info { |
| /// |
| /// This is the flag field for the PXE_DB_GET_CONFIG_INFO union. |
| /// For PCI bus devices, this field is set to PXE_BUSTYPE_PCI. |
| /// |
| UINT32 BusType; |
| |
| /// |
| /// This identifies the PCI network device that this UNDI interface |
| /// is bound to. |
| /// |
| UINT16 Bus; |
| UINT8 Device; |
| UINT8 Function; |
| |
| /// |
| /// This is a copy of the PCI configuration space for this |
| /// network device. |
| /// |
| union { |
| UINT8 Byte[256]; |
| UINT16 Word[128]; |
| UINT32 Dword[64]; |
| } Config; |
| } PXE_PCI_CONFIG_INFO; |
| |
| typedef struct s_pxe_pcc_config_info { |
| /// |
| /// This is the flag field for the PXE_DB_GET_CONFIG_INFO union. |
| /// For PCC bus devices, this field is set to PXE_BUSTYPE_PCC. |
| /// |
| PXE_UINT32 BusType; |
| |
| /// |
| /// This identifies the PCC network device that this UNDI interface |
| /// is bound to. |
| /// |
| PXE_UINT16 Bus; |
| PXE_UINT8 Device; |
| PXE_UINT8 Function; |
| |
| /// |
| /// This is a copy of the PCC configuration space for this |
| /// network device. |
| /// |
| union { |
| PXE_UINT8 Byte[256]; |
| PXE_UINT16 Word[128]; |
| PXE_UINT32 Dword[64]; |
| } Config; |
| } PXE_PCC_CONFIG_INFO; |
| |
| typedef union u_pxe_db_get_config_info { |
| PXE_PCI_CONFIG_INFO pci; |
| PXE_PCC_CONFIG_INFO pcc; |
| } PXE_DB_GET_CONFIG_INFO; |
| |
| typedef struct s_pxe_cpb_initialize { |
| /// |
| /// Address of first (lowest) byte of the memory buffer. This buffer must |
| /// be in contiguous physical memory and cannot be swapped out. The UNDI |
| /// will be using this for transmit and receive buffering. |
| /// |
| PXE_UINT64 MemoryAddr; |
| |
| /// |
| /// MemoryLength must be greater than or equal to MemoryRequired |
| /// returned by the Get Init Info command. |
| /// |
| PXE_UINT32 MemoryLength; |
| |
| /// |
| /// Desired link speed in Mbit/sec. Common ethernet values are 10, 100 |
| /// and 1000. Setting a value of zero will auto-detect and/or use the |
| /// default link speed (operation depends on UNDI/NIC functionality). |
| /// |
| PXE_UINT32 LinkSpeed; |
| |
| /// |
| /// Suggested number and size of receive and transmit buffers to |
| /// allocate. If MemoryAddr and MemoryLength are non-zero, this |
| /// allocation comes out of the supplied memory buffer. If MemoryAddr |
| /// and MemoryLength are zero, this allocation comes out of memory |
| /// on the NIC. |
| /// |
| /// If these fields are set to zero, the UNDI will allocate buffer |
| /// counts and sizes as it sees fit. |
| /// |
| PXE_UINT16 TxBufCnt; |
| PXE_UINT16 TxBufSize; |
| PXE_UINT16 RxBufCnt; |
| PXE_UINT16 RxBufSize; |
| |
| /// |
| /// The following configuration parameters are optional and must be zero |
| /// to use the default values. |
| /// |
| PXE_UINT8 DuplexMode; |
| |
| PXE_UINT8 LoopBackMode; |
| } PXE_CPB_INITIALIZE; |
| |
| #define PXE_DUPLEX_DEFAULT 0x00 |
| #define PXE_FORCE_FULL_DUPLEX 0x01 |
| #define PXE_ENABLE_FULL_DUPLEX 0x02 |
| #define PXE_FORCE_HALF_DUPLEX 0x04 |
| #define PXE_DISABLE_FULL_DUPLEX 0x08 |
| |
| #define LOOPBACK_NORMAL 0 |
| #define LOOPBACK_INTERNAL 1 |
| #define LOOPBACK_EXTERNAL 2 |
| |
| typedef struct s_pxe_db_initialize { |
| /// |
| /// Actual amount of memory used from the supplied memory buffer. This |
| /// may be less that the amount of memory suppllied and may be zero if |
| /// the UNDI and network device do not use external memory buffers. |
| /// |
| /// Memory used by the UNDI and network device is allocated from the |
| /// lowest memory buffer address. |
| /// |
| PXE_UINT32 MemoryUsed; |
| |
| /// |
| /// Actual number and size of receive and transmit buffers that were |
| /// allocated. |
| /// |
| PXE_UINT16 TxBufCnt; |
| PXE_UINT16 TxBufSize; |
| PXE_UINT16 RxBufCnt; |
| PXE_UINT16 RxBufSize; |
| } PXE_DB_INITIALIZE; |
| |
| typedef struct s_pxe_cpb_receive_filters { |
| /// |
| /// List of multicast MAC addresses. This list, if present, will |
| /// replace the existing multicast MAC address filter list. |
| /// |
| PXE_MAC_ADDR MCastList[MAX_MCAST_ADDRESS_CNT]; |
| } PXE_CPB_RECEIVE_FILTERS; |
| |
| typedef struct s_pxe_db_receive_filters { |
| /// |
| /// Filtered multicast MAC address list. |
| /// |
| PXE_MAC_ADDR MCastList[MAX_MCAST_ADDRESS_CNT]; |
| } PXE_DB_RECEIVE_FILTERS; |
| |
| typedef struct s_pxe_cpb_station_address { |
| /// |
| /// If supplied and supported, the current station MAC address |
| /// will be changed. |
| /// |
| PXE_MAC_ADDR StationAddr; |
| } PXE_CPB_STATION_ADDRESS; |
| |
| typedef struct s_pxe_dpb_station_address { |
| /// |
| /// Current station MAC address. |
| /// |
| PXE_MAC_ADDR StationAddr; |
| |
| /// |
| /// Station broadcast MAC address. |
| /// |
| PXE_MAC_ADDR BroadcastAddr; |
| |
| /// |
| /// Permanent station MAC address. |
| /// |
| PXE_MAC_ADDR PermanentAddr; |
| } PXE_DB_STATION_ADDRESS; |
| |
| typedef struct s_pxe_db_statistics { |
| /// |
| /// Bit field identifying what statistic data is collected by the |
| /// UNDI/NIC. |
| /// If bit 0x00 is set, Data[0x00] is collected. |
| /// If bit 0x01 is set, Data[0x01] is collected. |
| /// If bit 0x20 is set, Data[0x20] is collected. |
| /// If bit 0x21 is set, Data[0x21] is collected. |
| /// Etc. |
| /// |
| PXE_UINT64 Supported; |
| |
| /// |
| /// Statistic data. |
| /// |
| PXE_UINT64 Data[64]; |
| } PXE_DB_STATISTICS; |
| |
| /// |
| /// Total number of frames received. Includes frames with errors and |
| /// dropped frames. |
| /// |
| #define PXE_STATISTICS_RX_TOTAL_FRAMES 0x00 |
| |
| /// |
| /// Number of valid frames received and copied into receive buffers. |
| /// |
| #define PXE_STATISTICS_RX_GOOD_FRAMES 0x01 |
| |
| /// |
| /// Number of frames below the minimum length for the media. |
| /// This would be <64 for ethernet. |
| /// |
| #define PXE_STATISTICS_RX_UNDERSIZE_FRAMES 0x02 |
| |
| /// |
| /// Number of frames longer than the maxminum length for the |
| /// media. This would be >1500 for ethernet. |
| /// |
| #define PXE_STATISTICS_RX_OVERSIZE_FRAMES 0x03 |
| |
| /// |
| /// Valid frames that were dropped because receive buffers were full. |
| /// |
| #define PXE_STATISTICS_RX_DROPPED_FRAMES 0x04 |
| |
| /// |
| /// Number of valid unicast frames received and not dropped. |
| /// |
| #define PXE_STATISTICS_RX_UNICAST_FRAMES 0x05 |
| |
| /// |
| /// Number of valid broadcast frames received and not dropped. |
| /// |
| #define PXE_STATISTICS_RX_BROADCAST_FRAMES 0x06 |
| |
| /// |
| /// Number of valid mutlicast frames received and not dropped. |
| /// |
| #define PXE_STATISTICS_RX_MULTICAST_FRAMES 0x07 |
| |
| /// |
| /// Number of frames w/ CRC or alignment errors. |
| /// |
| #define PXE_STATISTICS_RX_CRC_ERROR_FRAMES 0x08 |
| |
| /// |
| /// Total number of bytes received. Includes frames with errors |
| /// and dropped frames. |
| /// |
| #define PXE_STATISTICS_RX_TOTAL_BYTES 0x09 |
| |
| /// |
| /// Transmit statistics. |
| /// |
| #define PXE_STATISTICS_TX_TOTAL_FRAMES 0x0A |
| #define PXE_STATISTICS_TX_GOOD_FRAMES 0x0B |
| #define PXE_STATISTICS_TX_UNDERSIZE_FRAMES 0x0C |
| #define PXE_STATISTICS_TX_OVERSIZE_FRAMES 0x0D |
| #define PXE_STATISTICS_TX_DROPPED_FRAMES 0x0E |
| #define PXE_STATISTICS_TX_UNICAST_FRAMES 0x0F |
| #define PXE_STATISTICS_TX_BROADCAST_FRAMES 0x10 |
| #define PXE_STATISTICS_TX_MULTICAST_FRAMES 0x11 |
| #define PXE_STATISTICS_TX_CRC_ERROR_FRAMES 0x12 |
| #define PXE_STATISTICS_TX_TOTAL_BYTES 0x13 |
| |
| /// |
| /// Number of collisions detection on this subnet. |
| /// |
| #define PXE_STATISTICS_COLLISIONS 0x14 |
| |
| /// |
| /// Number of frames destined for unsupported protocol. |
| /// |
| #define PXE_STATISTICS_UNSUPPORTED_PROTOCOL 0x15 |
| |
| typedef struct s_pxe_cpb_mcast_ip_to_mac { |
| /// |
| /// Multicast IP address to be converted to multicast MAC address. |
| /// |
| PXE_IP_ADDR IP; |
| } PXE_CPB_MCAST_IP_TO_MAC; |
| |
| typedef struct s_pxe_db_mcast_ip_to_mac { |
| /// |
| /// Multicast MAC address. |
| /// |
| PXE_MAC_ADDR MAC; |
| } PXE_DB_MCAST_IP_TO_MAC; |
| |
| typedef struct s_pxe_cpb_nvdata_sparse { |
| /// |
| /// NvData item list. Only items in this list will be updated. |
| /// |
| struct { |
| /// |
| /// Non-volatile storage address to be changed. |
| /// |
| PXE_UINT32 Addr; |
| |
| /// |
| /// Data item to write into above storage address. |
| /// |
| union { |
| PXE_UINT8 Byte; |
| PXE_UINT16 Word; |
| PXE_UINT32 Dword; |
| } Data; |
| } Item[MAX_EEPROM_LEN]; |
| } PXE_CPB_NVDATA_SPARSE; |
| |
| /// |
| /// When using bulk update, the size of the CPB structure must be |
| /// the same size as the non-volatile NIC storage. |
| /// |
| typedef union u_pxe_cpb_nvdata_bulk { |
| /// |
| /// Array of byte-wide data items. |
| /// |
| PXE_UINT8 Byte[MAX_EEPROM_LEN << 2]; |
| |
| /// |
| /// Array of word-wide data items. |
| /// |
| PXE_UINT16 Word[MAX_EEPROM_LEN << 1]; |
| |
| /// |
| /// Array of dword-wide data items. |
| /// |
| PXE_UINT32 Dword[MAX_EEPROM_LEN]; |
| } PXE_CPB_NVDATA_BULK; |
| |
| typedef struct s_pxe_db_nvdata { |
| /// |
| /// Arrays of data items from non-volatile storage. |
| /// |
| union { |
| /// |
| /// Array of byte-wide data items. |
| /// |
| PXE_UINT8 Byte[MAX_EEPROM_LEN << 2]; |
| |
| /// |
| /// Array of word-wide data items. |
| /// |
| PXE_UINT16 Word[MAX_EEPROM_LEN << 1]; |
| |
| /// |
| /// Array of dword-wide data items. |
| /// |
| PXE_UINT32 Dword[MAX_EEPROM_LEN]; |
| } Data; |
| } PXE_DB_NVDATA; |
| |
| typedef struct s_pxe_db_get_status { |
| /// |
| /// Length of next receive frame (header + data). If this is zero, |
| /// there is no next receive frame available. |
| /// |
| PXE_UINT32 RxFrameLen; |
| |
| /// |
| /// Reserved, set to zero. |
| /// |
| PXE_UINT32 reserved; |
| |
| /// |
| /// Addresses of transmitted buffers that need to be recycled. |
| /// |
| PXE_UINT64 TxBuffer[MAX_XMIT_BUFFERS]; |
| } PXE_DB_GET_STATUS; |
| |
| typedef struct s_pxe_cpb_fill_header { |
| /// |
| /// Source and destination MAC addresses. These will be copied into |
| /// the media header without doing byte swapping. |
| /// |
| PXE_MAC_ADDR SrcAddr; |
| PXE_MAC_ADDR DestAddr; |
| |
| /// |
| /// Address of first byte of media header. The first byte of packet data |
| /// follows the last byte of the media header. |
| /// |
| PXE_UINT64 MediaHeader; |
| |
| /// |
| /// Length of packet data in bytes (not including the media header). |
| /// |
| PXE_UINT32 PacketLen; |
| |
| /// |
| /// Protocol type. This will be copied into the media header without |
| /// doing byte swapping. Protocol type numbers can be obtained from |
| /// the Assigned Numbers RFC 1700. |
| /// |
| PXE_UINT16 Protocol; |
| |
| /// |
| /// Length of the media header in bytes. |
| /// |
| PXE_UINT16 MediaHeaderLen; |
| } PXE_CPB_FILL_HEADER; |
| |
| #define PXE_PROTOCOL_ETHERNET_IP 0x0800 |
| #define PXE_PROTOCOL_ETHERNET_ARP 0x0806 |
| #define MAX_XMIT_FRAGMENTS 16 |
| |
| typedef struct s_pxe_cpb_fill_header_fragmented { |
| /// |
| /// Source and destination MAC addresses. These will be copied into |
| /// the media header without doing byte swapping. |
| /// |
| PXE_MAC_ADDR SrcAddr; |
| PXE_MAC_ADDR DestAddr; |
| |
| /// |
| /// Length of packet data in bytes (not including the media header). |
| /// |
| PXE_UINT32 PacketLen; |
| |
| /// |
| /// Protocol type. This will be copied into the media header without |
| /// doing byte swapping. Protocol type numbers can be obtained from |
| /// the Assigned Numbers RFC 1700. |
| /// |
| PXE_MEDIA_PROTOCOL Protocol; |
| |
| /// |
| /// Length of the media header in bytes. |
| /// |
| PXE_UINT16 MediaHeaderLen; |
| |
| /// |
| /// Number of packet fragment descriptors. |
| /// |
| PXE_UINT16 FragCnt; |
| |
| /// |
| /// Reserved, must be set to zero. |
| /// |
| PXE_UINT16 reserved; |
| |
| /// |
| /// Array of packet fragment descriptors. The first byte of the media |
| /// header is the first byte of the first fragment. |
| /// |
| struct { |
| /// |
| /// Address of this packet fragment. |
| /// |
| PXE_UINT64 FragAddr; |
| |
| /// |
| /// Length of this packet fragment. |
| /// |
| PXE_UINT32 FragLen; |
| |
| /// |
| /// Reserved, must be set to zero. |
| /// |
| PXE_UINT32 reserved; |
| } FragDesc[MAX_XMIT_FRAGMENTS]; |
| } |
| PXE_CPB_FILL_HEADER_FRAGMENTED; |
| |
| typedef struct s_pxe_cpb_transmit { |
| /// |
| /// Address of first byte of frame buffer. This is also the first byte |
| /// of the media header. |
| /// |
| PXE_UINT64 FrameAddr; |
| |
| /// |
| /// Length of the data portion of the frame buffer in bytes. Do not |
| /// include the length of the media header. |
| /// |
| PXE_UINT32 DataLen; |
| |
| /// |
| /// Length of the media header in bytes. |
| /// |
| PXE_UINT16 MediaheaderLen; |
| |
| /// |
| /// Reserved, must be zero. |
| /// |
| PXE_UINT16 reserved; |
| } PXE_CPB_TRANSMIT; |
| |
| typedef struct s_pxe_cpb_transmit_fragments { |
| /// |
| /// Length of packet data in bytes (not including the media header). |
| /// |
| PXE_UINT32 FrameLen; |
| |
| /// |
| /// Length of the media header in bytes. |
| /// |
| PXE_UINT16 MediaheaderLen; |
| |
| /// |
| /// Number of packet fragment descriptors. |
| /// |
| PXE_UINT16 FragCnt; |
| |
| /// |
| /// Array of frame fragment descriptors. The first byte of the first |
| /// fragment is also the first byte of the media header. |
| /// |
| struct { |
| /// |
| /// Address of this frame fragment. |
| /// |
| PXE_UINT64 FragAddr; |
| |
| /// |
| /// Length of this frame fragment. |
| /// |
| PXE_UINT32 FragLen; |
| |
| /// |
| /// Reserved, must be set to zero. |
| /// |
| PXE_UINT32 reserved; |
| } FragDesc[MAX_XMIT_FRAGMENTS]; |
| } |
| PXE_CPB_TRANSMIT_FRAGMENTS; |
| |
| typedef struct s_pxe_cpb_receive { |
| /// |
| /// Address of first byte of receive buffer. This is also the first byte |
| /// of the frame header. |
| /// |
| PXE_UINT64 BufferAddr; |
| |
| /// |
| /// Length of receive buffer. This must be large enough to hold the |
| /// received frame (media header + data). If the length of smaller than |
| /// the received frame, data will be lost. |
| /// |
| PXE_UINT32 BufferLen; |
| |
| /// |
| /// Reserved, must be set to zero. |
| /// |
| PXE_UINT32 reserved; |
| } PXE_CPB_RECEIVE; |
| |
| typedef struct s_pxe_db_receive { |
| /// |
| /// Source and destination MAC addresses from media header. |
| /// |
| PXE_MAC_ADDR SrcAddr; |
| PXE_MAC_ADDR DestAddr; |
| |
| /// |
| /// Length of received frame. May be larger than receive buffer size. |
| /// The receive buffer will not be overwritten. This is how to tell |
| /// if data was lost because the receive buffer was too small. |
| /// |
| PXE_UINT32 FrameLen; |
| |
| /// |
| /// Protocol type from media header. |
| /// |
| PXE_MEDIA_PROTOCOL Protocol; |
| |
| /// |
| /// Length of media header in received frame. |
| /// |
| PXE_UINT16 MediaHeaderLen; |
| |
| /// |
| /// Type of receive frame. |
| /// |
| PXE_FRAME_TYPE Type; |
| |
| /// |
| /// Reserved, must be zero. |
| /// |
| PXE_UINT8 reserved[7]; |
| |
| } PXE_DB_RECEIVE; |
| |
| #pragma pack() |
| |
| #endif |