Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs. Some for SoC-family code under
drivers/soc, but also some other driver updates that don't belong
anywhere else. We also bring in the drivers/reset code through
arm-soc.
Some of the larger updates:
- Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate
with other parts of the chip/board on these platforms, all
proprietary protocols that don't fit into other subsystems and live
in drivers/soc for now.
- System bus driver for UniPhier
- Driver for the TI Wakeup M3 IPC device
- Power management for Raspberry PI
+ Again a bunch of other smaller updates and patches"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: uniphier: allow only built-in driver
ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
MAINTAINERS: Drop Kumar Gala from QCOM
bus: uniphier-system-bus: add UniPhier System Bus driver
ARM: bcm2835: add rpi power domain driver
dt-bindings: add rpi power domain driver bindings
ARM: bcm2835: Define two new packets from the latest firmware.
drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
soc: mediatek: SCPSYS: Add regulator support
MAINTAINERS: Change QCOM entries
soc: qcom: smd-rpm: Add existing platform support
memory/tegra: Add number of TLB lines for Tegra124
reset: hi6220: fix modular build
soc: qcom: Introduce WCNSS_CTRL SMD client
ARM: qcom: select ARM_CPU_SUSPEND for power management
MAINTAINERS: Add rules for Qualcomm dts files
soc: qcom: enable smsm/smp2p modular build
serial: msm_serial: Make config tristate
soc: qcom: smp2p: Qualcomm Shared Memory Point to Point
soc: qcom: smsm: Add driver for Qualcomm SMSM
...
diff --git a/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt b/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt
new file mode 100644
index 0000000..68ef80a
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/uniphier-system-bus.txt
@@ -0,0 +1,66 @@
+UniPhier System Bus
+
+The UniPhier System Bus is an external bus that connects on-board devices to
+the UniPhier SoC. It is a simple (semi-)parallel bus with address, data, and
+some control signals. It supports up to 8 banks (chip selects).
+
+Before any access to the bus, the bus controller must be configured; the bus
+controller registers provide the control for the translation from the offset
+within each bank to the CPU-viewed address. The needed setup includes the base
+address, the size of each bank. Optionally, some timing parameters can be
+optimized for faster bus access.
+
+Required properties:
+- compatible: should be "socionext,uniphier-system-bus".
+- reg: offset and length of the register set for the bus controller device.
+- #address-cells: should be 2. The first cell is the bank number (chip select).
+ The second cell is the address offset within the bank.
+- #size-cells: should be 1.
+- ranges: should provide a proper address translation from the System Bus to
+ the parent bus.
+
+Note:
+The address region(s) that can be assigned for the System Bus is implementation
+defined. Some SoCs can use 0x00000000-0x0fffffff and 0x40000000-0x4fffffff,
+while other SoCs can only use 0x40000000-0x4fffffff. There might be additional
+limitations depending on SoCs and the boot mode. The address translation is
+arbitrary as long as the banks are assigned in the supported address space with
+the required alignment and they do not overlap one another.
+For example, it is possible to map:
+ bank 0 to 0x42000000-0x43ffffff, bank 5 to 0x46000000-0x46ffffff
+It is also possible to map:
+ bank 0 to 0x48000000-0x49ffffff, bank 5 to 0x44000000-0x44ffffff
+There is no reason to stick to a particular translation mapping, but the
+"ranges" property should provide a "reasonable" default that is known to work.
+The software should initialize the bus controller according to it.
+
+Example:
+
+ system-bus {
+ compatible = "socionext,uniphier-system-bus";
+ reg = <0x58c00000 0x400>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <1 0x00000000 0x42000000 0x02000000
+ 5 0x00000000 0x46000000 0x01000000>;
+
+ ethernet@1,01f00000 {
+ compatible = "smsc,lan9115";
+ reg = <1 0x01f00000 0x1000>;
+ interrupts = <0 48 4>
+ phy-mode = "mii";
+ };
+
+ uart@5,00200000 {
+ compatible = "ns16550a";
+ reg = <5 0x00200000 0x20>;
+ interrupts = <0 49 4>
+ clock-frequency = <12288000>;
+ };
+ };
+
+In this example,
+ - the Ethernet device is connected at the offset 0x01f00000 of CS1 and
+ mapped to 0x43f00000 of the parent bus.
+ - the UART device is connected at the offset 0x00200000 of CS5 and
+ mapped to 0x46200000 of the parent bus.
diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt
new file mode 100644
index 0000000..e0b185a
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt
@@ -0,0 +1,34 @@
+Hisilicon System Reset Controller
+======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+The reset controller registers are part of the system-ctl block on
+hi6220 SoC.
+
+Required properties:
+- compatible: may be "hisilicon,hi6220-sysctrl"
+- reg: should be register base and length as documented in the
+ datasheet
+- #reset-cells: 1, see below
+
+Example:
+sys_ctrl: sys_ctrl@f7030000 {
+ compatible = "hisilicon,hi6220-sysctrl", "syscon";
+ reg = <0x0 0xf7030000 0x0 0x2000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+};
+
+Specifying reset lines connected to IP modules
+==============================================
+example:
+
+ uart1: serial@..... {
+ ...
+ resets = <&sys_ctrl PERIPH_RSTEN3_UART1>;
+ ...
+ };
+
+The index could be found in <dt-bindings/reset/hisi,hi6220-resets.h>.
diff --git a/Documentation/devicetree/bindings/soc/bcm/raspberrypi,bcm2835-power.txt b/Documentation/devicetree/bindings/soc/bcm/raspberrypi,bcm2835-power.txt
new file mode 100644
index 0000000..30942cf
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/bcm/raspberrypi,bcm2835-power.txt
@@ -0,0 +1,47 @@
+Raspberry Pi power domain driver
+
+Required properties:
+
+- compatible: Should be "raspberrypi,bcm2835-power".
+- firmware: Reference to the RPi firmware device node.
+- #power-domain-cells: Should be <1>, we providing multiple power domains.
+
+The valid defines for power domain are:
+
+ RPI_POWER_DOMAIN_I2C0
+ RPI_POWER_DOMAIN_I2C1
+ RPI_POWER_DOMAIN_I2C2
+ RPI_POWER_DOMAIN_VIDEO_SCALER
+ RPI_POWER_DOMAIN_VPU1
+ RPI_POWER_DOMAIN_HDMI
+ RPI_POWER_DOMAIN_USB
+ RPI_POWER_DOMAIN_VEC
+ RPI_POWER_DOMAIN_JPEG
+ RPI_POWER_DOMAIN_H264
+ RPI_POWER_DOMAIN_V3D
+ RPI_POWER_DOMAIN_ISP
+ RPI_POWER_DOMAIN_UNICAM0
+ RPI_POWER_DOMAIN_UNICAM1
+ RPI_POWER_DOMAIN_CCP2RX
+ RPI_POWER_DOMAIN_CSI2
+ RPI_POWER_DOMAIN_CPI
+ RPI_POWER_DOMAIN_DSI0
+ RPI_POWER_DOMAIN_DSI1
+ RPI_POWER_DOMAIN_TRANSPOSER
+ RPI_POWER_DOMAIN_CCP2TX
+ RPI_POWER_DOMAIN_CDP
+ RPI_POWER_DOMAIN_ARM
+
+Example:
+
+power: power {
+ compatible = "raspberrypi,bcm2835-power";
+ firmware = <&firmware>;
+ #power-domain-cells = <1>;
+};
+
+Example for using power domain:
+
+&usb {
+ power-domains = <&power RPI_POWER_DOMAIN_USB>;
+};
diff --git a/Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt b/Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt
new file mode 100644
index 0000000..4015504
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt
@@ -0,0 +1,57 @@
+Wakeup M3 IPC Driver
+=====================
+
+The TI AM33xx and AM43xx family of devices use a small Cortex M3 co-processor
+(commonly referred to as Wakeup M3 or CM3) to help with various low power tasks
+that cannot be controlled from the MPU, like suspend/resume and certain deep
+C-states for CPU Idle. Once the wkup_m3_ipc driver uses the wkup_m3_rproc driver
+to boot the wkup_m3, it handles communication with the CM3 using IPC registers
+present in the SoC's control module and a mailbox. The wkup_m3_ipc exposes an
+API to allow the SoC PM code to execute specific PM tasks.
+
+Wkup M3 Device Node:
+====================
+A wkup_m3_ipc device node is used to represent the IPC registers within an
+SoC.
+
+Required properties:
+--------------------
+- compatible: Should be,
+ "ti,am3352-wkup-m3-ipc" for AM33xx SoCs
+ "ti,am4372-wkup-m3-ipc" for AM43xx SoCs
+- reg: Contains the IPC register address space to communicate
+ with the Wakeup M3 processor
+- interrupts: Contains the interrupt information for the wkup_m3
+ interrupt that signals the MPU.
+- ti,rproc: phandle to the wkup_m3 rproc node so the IPC driver
+ can boot it.
+- mboxes: phandles used by IPC framework to get correct mbox
+ channel for communication. Must point to appropriate
+ mbox_wkupm3 child node.
+
+Example:
+--------
+/* AM33xx */
+ l4_wkup: l4_wkup@44c00000 {
+ ...
+
+ scm: scm@210000 {
+ compatible = "ti,am3-scm", "simple-bus";
+ reg = <0x210000 0x2000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x210000 0x2000>;
+
+ ...
+
+ wkup_m3_ipc: wkup_m3_ipc@1324 {
+ compatible = "ti,am3352-wkup-m3-ipc";
+ reg = <0x1324 0x24>;
+ interrupts = <78>;
+ ti,rproc = <&wkup_m3>;
+ mboxes = <&mailbox &mbox_wkupm3>;
+ };
+
+ ...
+ };
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 9268e83..db68d7f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1415,12 +1415,13 @@
S: Maintained
ARM/QUALCOMM SUPPORT
-M: Kumar Gala <galak@codeaurora.org>
-M: Andy Gross <agross@codeaurora.org>
-M: David Brown <davidb@codeaurora.org>
+M: Andy Gross <andy.gross@linaro.org>
+M: David Brown <david.brown@linaro.org>
L: linux-arm-msm@vger.kernel.org
L: linux-soc@vger.kernel.org
S: Maintained
+F: arch/arm/boot/dts/qcom-*.dts
+F: arch/arm/boot/dts/qcom-*.dtsi
F: arch/arm/mach-qcom/
F: drivers/soc/qcom/
F: drivers/tty/serial/msm_serial.h
@@ -1428,7 +1429,7 @@
F: drivers/*/pm8???-*
F: drivers/mfd/ssbi.c
F: drivers/firmware/qcom_scm.c
-T: git git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux.git
ARM/RADISYS ENP2611 MACHINE SUPPORT
M: Lennert Buytenhek <kernel@wantstofly.org>
@@ -1673,6 +1674,7 @@
F: arch/arm/mach-uniphier/
F: arch/arm/mm/cache-uniphier.c
F: arch/arm64/boot/dts/socionext/
+F: drivers/bus/uniphier-system-bus.c
F: drivers/i2c/busses/i2c-uniphier*
F: drivers/pinctrl/uniphier/
F: drivers/tty/serial/8250/8250_uniphier.c
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index 82d2488..ad1f1eb 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -147,6 +147,7 @@
compatible = "hisilicon,hi6220-sysctrl", "syscon";
reg = <0x0 0xf7030000 0x0 0x2000>;
#clock-cells = <1>;
+ #reset-cells = <1>;
};
media_ctrl: media_ctrl@f4410000 {
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index 116b363..129d47b 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -131,6 +131,14 @@
with various RSB based devices, such as AXP223, AXP8XX PMICs,
and AC100/AC200 ICs.
+config UNIPHIER_SYSTEM_BUS
+ bool "UniPhier System Bus driver"
+ depends on ARCH_UNIPHIER && OF
+ default y
+ help
+ Support for UniPhier System Bus, a simple external bus. This is
+ needed to use on-board devices connected to UniPhier SoCs.
+
config VEXPRESS_CONFIG
bool "Versatile Express configuration bus"
default y if ARCH_VEXPRESS
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
index fcb9f97..ccff007 100644
--- a/drivers/bus/Makefile
+++ b/drivers/bus/Makefile
@@ -17,4 +17,5 @@
obj-$(CONFIG_OMAP_OCP2SCP) += omap-ocp2scp.o
obj-$(CONFIG_SUNXI_RSB) += sunxi-rsb.o
obj-$(CONFIG_SIMPLE_PM_BUS) += simple-pm-bus.o
+obj-$(CONFIG_UNIPHIER_SYSTEM_BUS) += uniphier-system-bus.o
obj-$(CONFIG_VEXPRESS_CONFIG) += vexpress-config.o
diff --git a/drivers/bus/uniphier-system-bus.c b/drivers/bus/uniphier-system-bus.c
new file mode 100644
index 0000000..834a2ae
--- /dev/null
+++ b/drivers/bus/uniphier-system-bus.c
@@ -0,0 +1,281 @@
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/log2.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+/* System Bus Controller registers */
+#define UNIPHIER_SBC_BASE 0x100 /* base address of bank0 space */
+#define UNIPHIER_SBC_BASE_BE BIT(0) /* bank_enable */
+#define UNIPHIER_SBC_CTRL0 0x200 /* timing parameter 0 of bank0 */
+#define UNIPHIER_SBC_CTRL1 0x204 /* timing parameter 1 of bank0 */
+#define UNIPHIER_SBC_CTRL2 0x208 /* timing parameter 2 of bank0 */
+#define UNIPHIER_SBC_CTRL3 0x20c /* timing parameter 3 of bank0 */
+#define UNIPHIER_SBC_CTRL4 0x300 /* timing parameter 4 of bank0 */
+
+#define UNIPHIER_SBC_STRIDE 0x10 /* register stride to next bank */
+#define UNIPHIER_SBC_NR_BANKS 8 /* number of banks (chip select) */
+#define UNIPHIER_SBC_BASE_DUMMY 0xffffffff /* data to squash bank 0, 1 */
+
+struct uniphier_system_bus_bank {
+ u32 base;
+ u32 end;
+};
+
+struct uniphier_system_bus_priv {
+ struct device *dev;
+ void __iomem *membase;
+ struct uniphier_system_bus_bank bank[UNIPHIER_SBC_NR_BANKS];
+};
+
+static int uniphier_system_bus_add_bank(struct uniphier_system_bus_priv *priv,
+ int bank, u32 addr, u64 paddr, u32 size)
+{
+ u64 end, mask;
+
+ dev_dbg(priv->dev,
+ "range found: bank = %d, addr = %08x, paddr = %08llx, size = %08x\n",
+ bank, addr, paddr, size);
+
+ if (bank >= ARRAY_SIZE(priv->bank)) {
+ dev_err(priv->dev, "unsupported bank number %d\n", bank);
+ return -EINVAL;
+ }
+
+ if (priv->bank[bank].base || priv->bank[bank].end) {
+ dev_err(priv->dev,
+ "range for bank %d has already been specified\n", bank);
+ return -EINVAL;
+ }
+
+ if (paddr > U32_MAX) {
+ dev_err(priv->dev, "base address %llx is too high\n", paddr);
+ return -EINVAL;
+ }
+
+ end = paddr + size;
+
+ if (addr > paddr) {
+ dev_err(priv->dev,
+ "base %08x cannot be mapped to %08llx of parent\n",
+ addr, paddr);
+ return -EINVAL;
+ }
+ paddr -= addr;
+
+ paddr = round_down(paddr, 0x00020000);
+ end = round_up(end, 0x00020000);
+
+ if (end > U32_MAX) {
+ dev_err(priv->dev, "end address %08llx is too high\n", end);
+ return -EINVAL;
+ }
+ mask = paddr ^ (end - 1);
+ mask = roundup_pow_of_two(mask);
+
+ paddr = round_down(paddr, mask);
+ end = round_up(end, mask);
+
+ priv->bank[bank].base = paddr;
+ priv->bank[bank].end = end;
+
+ dev_dbg(priv->dev, "range added: bank = %d, addr = %08x, end = %08x\n",
+ bank, priv->bank[bank].base, priv->bank[bank].end);
+
+ return 0;
+}
+
+static int uniphier_system_bus_check_overlap(
+ const struct uniphier_system_bus_priv *priv)
+{
+ int i, j;
+
+ for (i = 0; i < ARRAY_SIZE(priv->bank); i++) {
+ for (j = i + 1; j < ARRAY_SIZE(priv->bank); j++) {
+ if (priv->bank[i].end > priv->bank[j].base ||
+ priv->bank[i].base < priv->bank[j].end) {
+ dev_err(priv->dev,
+ "region overlap between bank%d and bank%d\n",
+ i, j);
+ return -EINVAL;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static void uniphier_system_bus_check_boot_swap(
+ struct uniphier_system_bus_priv *priv)
+{
+ void __iomem *base_reg = priv->membase + UNIPHIER_SBC_BASE;
+ int is_swapped;
+
+ is_swapped = !(readl(base_reg) & UNIPHIER_SBC_BASE_BE);
+
+ dev_dbg(priv->dev, "Boot Swap: %s\n", is_swapped ? "on" : "off");
+
+ /*
+ * If BOOT_SWAP was asserted on power-on-reset, the CS0 and CS1 are
+ * swapped. In this case, bank0 and bank1 should be swapped as well.
+ */
+ if (is_swapped)
+ swap(priv->bank[0], priv->bank[1]);
+}
+
+static void uniphier_system_bus_set_reg(
+ const struct uniphier_system_bus_priv *priv)
+{
+ void __iomem *base_reg = priv->membase + UNIPHIER_SBC_BASE;
+ u32 base, end, mask, val;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(priv->bank); i++) {
+ base = priv->bank[i].base;
+ end = priv->bank[i].end;
+
+ if (base == end) {
+ /*
+ * If SBC_BASE0 or SBC_BASE1 is set to zero, the access
+ * to anywhere in the system bus space is routed to
+ * bank 0 (if boot swap if off) or bank 1 (if boot swap
+ * if on). It means that CPUs cannot get access to
+ * bank 2 or later. In other words, bank 0/1 cannot
+ * be disabled even if its bank_enable bits is cleared.
+ * This seems odd, but it is how this hardware goes.
+ * As a workaround, dummy data (0xffffffff) should be
+ * set when the bank 0/1 is unused. As for bank 2 and
+ * later, they can be simply disable by clearing the
+ * bank_enable bit.
+ */
+ if (i < 2)
+ val = UNIPHIER_SBC_BASE_DUMMY;
+ else
+ val = 0;
+ } else {
+ mask = base ^ (end - 1);
+
+ val = base & 0xfffe0000;
+ val |= (~mask >> 16) & 0xfffe;
+ val |= UNIPHIER_SBC_BASE_BE;
+ }
+ dev_dbg(priv->dev, "SBC_BASE[%d] = 0x%08x\n", i, val);
+
+ writel(val, base_reg + UNIPHIER_SBC_STRIDE * i);
+ }
+}
+
+static int uniphier_system_bus_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct uniphier_system_bus_priv *priv;
+ struct resource *regs;
+ const __be32 *ranges;
+ u32 cells, addr, size;
+ u64 paddr;
+ int pna, bank, rlen, rone, ret;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->membase = devm_ioremap_resource(dev, regs);
+ if (IS_ERR(priv->membase))
+ return PTR_ERR(priv->membase);
+
+ priv->dev = dev;
+
+ pna = of_n_addr_cells(dev->of_node);
+
+ ret = of_property_read_u32(dev->of_node, "#address-cells", &cells);
+ if (ret) {
+ dev_err(dev, "failed to get #address-cells\n");
+ return ret;
+ }
+ if (cells != 2) {
+ dev_err(dev, "#address-cells must be 2\n");
+ return -EINVAL;
+ }
+
+ ret = of_property_read_u32(dev->of_node, "#size-cells", &cells);
+ if (ret) {
+ dev_err(dev, "failed to get #size-cells\n");
+ return ret;
+ }
+ if (cells != 1) {
+ dev_err(dev, "#size-cells must be 1\n");
+ return -EINVAL;
+ }
+
+ ranges = of_get_property(dev->of_node, "ranges", &rlen);
+ if (!ranges) {
+ dev_err(dev, "failed to get ranges property\n");
+ return -ENOENT;
+ }
+
+ rlen /= sizeof(*ranges);
+ rone = pna + 2;
+
+ for (; rlen >= rone; rlen -= rone) {
+ bank = be32_to_cpup(ranges++);
+ addr = be32_to_cpup(ranges++);
+ paddr = of_translate_address(dev->of_node, ranges);
+ if (paddr == OF_BAD_ADDR)
+ return -EINVAL;
+ ranges += pna;
+ size = be32_to_cpup(ranges++);
+
+ ret = uniphier_system_bus_add_bank(priv, bank, addr,
+ paddr, size);
+ if (ret)
+ return ret;
+ }
+
+ ret = uniphier_system_bus_check_overlap(priv);
+ if (ret)
+ return ret;
+
+ uniphier_system_bus_check_boot_swap(priv);
+
+ uniphier_system_bus_set_reg(priv);
+
+ /* Now, the bus is configured. Populate platform_devices below it */
+ return of_platform_populate(dev->of_node, of_default_bus_match_table,
+ NULL, dev);
+}
+
+static const struct of_device_id uniphier_system_bus_match[] = {
+ { .compatible = "socionext,uniphier-system-bus" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, uniphier_system_bus_match);
+
+static struct platform_driver uniphier_system_bus_driver = {
+ .probe = uniphier_system_bus_probe,
+ .driver = {
+ .name = "uniphier-system-bus",
+ .of_match_table = uniphier_system_bus_match,
+ },
+};
+module_platform_driver(uniphier_system_bus_driver);
+
+MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>");
+MODULE_DESCRIPTION("UniPhier System Bus driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/memory/tegra/tegra124.c b/drivers/memory/tegra/tegra124.c
index 21e7255..5a58e44 100644
--- a/drivers/memory/tegra/tegra124.c
+++ b/drivers/memory/tegra/tegra124.c
@@ -1007,6 +1007,7 @@
.num_swgroups = ARRAY_SIZE(tegra124_swgroups),
.supports_round_robin_arbitration = true,
.supports_request_limit = true,
+ .num_tlb_lines = 32,
.num_asids = 128,
};
diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
index 0615f50..df37212 100644
--- a/drivers/reset/Kconfig
+++ b/drivers/reset/Kconfig
@@ -13,3 +13,4 @@
If unsure, say no.
source "drivers/reset/sti/Kconfig"
+source "drivers/reset/hisilicon/Kconfig"
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index 85d5904..4d7178e 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -1,8 +1,9 @@
-obj-$(CONFIG_RESET_CONTROLLER) += core.o
+obj-y += core.o
obj-$(CONFIG_ARCH_LPC18XX) += reset-lpc18xx.o
obj-$(CONFIG_ARCH_SOCFPGA) += reset-socfpga.o
obj-$(CONFIG_ARCH_BERLIN) += reset-berlin.o
obj-$(CONFIG_ARCH_SUNXI) += reset-sunxi.o
obj-$(CONFIG_ARCH_STI) += sti/
+obj-$(CONFIG_ARCH_HISI) += hisilicon/
obj-$(CONFIG_ARCH_ZYNQ) += reset-zynq.o
obj-$(CONFIG_ATH79) += reset-ath79.o
diff --git a/drivers/reset/core.c b/drivers/reset/core.c
index 7955e00..8737663 100644
--- a/drivers/reset/core.c
+++ b/drivers/reset/core.c
@@ -30,7 +30,6 @@
*/
struct reset_control {
struct reset_controller_dev *rcdev;
- struct device *dev;
unsigned int id;
};
@@ -95,7 +94,7 @@
if (rstc->rcdev->ops->reset)
return rstc->rcdev->ops->reset(rstc->rcdev, rstc->id);
- return -ENOSYS;
+ return -ENOTSUPP;
}
EXPORT_SYMBOL_GPL(reset_control_reset);
@@ -108,7 +107,7 @@
if (rstc->rcdev->ops->assert)
return rstc->rcdev->ops->assert(rstc->rcdev, rstc->id);
- return -ENOSYS;
+ return -ENOTSUPP;
}
EXPORT_SYMBOL_GPL(reset_control_assert);
@@ -121,7 +120,7 @@
if (rstc->rcdev->ops->deassert)
return rstc->rcdev->ops->deassert(rstc->rcdev, rstc->id);
- return -ENOSYS;
+ return -ENOTSUPP;
}
EXPORT_SYMBOL_GPL(reset_control_deassert);
@@ -136,32 +135,29 @@
if (rstc->rcdev->ops->status)
return rstc->rcdev->ops->status(rstc->rcdev, rstc->id);
- return -ENOSYS;
+ return -ENOTSUPP;
}
EXPORT_SYMBOL_GPL(reset_control_status);
/**
- * of_reset_control_get - Lookup and obtain a reference to a reset controller.
+ * of_reset_control_get_by_index - Lookup and obtain a reference to a reset
+ * controller by index.
* @node: device to be reset by the controller
- * @id: reset line name
+ * @index: index of the reset controller
*
- * Returns a struct reset_control or IS_ERR() condition containing errno.
- *
- * Use of id names is optional.
+ * This is to be used to perform a list of resets for a device or power domain
+ * in whatever order. Returns a struct reset_control or IS_ERR() condition
+ * containing errno.
*/
-struct reset_control *of_reset_control_get(struct device_node *node,
- const char *id)
+struct reset_control *of_reset_control_get_by_index(struct device_node *node,
+ int index)
{
struct reset_control *rstc = ERR_PTR(-EPROBE_DEFER);
struct reset_controller_dev *r, *rcdev;
struct of_phandle_args args;
- int index = 0;
int rstc_id;
int ret;
- if (id)
- index = of_property_match_string(node,
- "reset-names", id);
ret = of_parse_phandle_with_args(node, "resets", "#reset-cells",
index, &args);
if (ret)
@@ -202,6 +198,30 @@
return rstc;
}
+EXPORT_SYMBOL_GPL(of_reset_control_get_by_index);
+
+/**
+ * of_reset_control_get - Lookup and obtain a reference to a reset controller.
+ * @node: device to be reset by the controller
+ * @id: reset line name
+ *
+ * Returns a struct reset_control or IS_ERR() condition containing errno.
+ *
+ * Use of id names is optional.
+ */
+struct reset_control *of_reset_control_get(struct device_node *node,
+ const char *id)
+{
+ int index = 0;
+
+ if (id) {
+ index = of_property_match_string(node,
+ "reset-names", id);
+ if (index < 0)
+ return ERR_PTR(-ENOENT);
+ }
+ return of_reset_control_get_by_index(node, index);
+}
EXPORT_SYMBOL_GPL(of_reset_control_get);
/**
@@ -215,16 +235,10 @@
*/
struct reset_control *reset_control_get(struct device *dev, const char *id)
{
- struct reset_control *rstc;
-
if (!dev)
return ERR_PTR(-EINVAL);
- rstc = of_reset_control_get(dev->of_node, id);
- if (!IS_ERR(rstc))
- rstc->dev = dev;
-
- return rstc;
+ return of_reset_control_get(dev->of_node, id);
}
EXPORT_SYMBOL_GPL(reset_control_get);
diff --git a/drivers/reset/hisilicon/Kconfig b/drivers/reset/hisilicon/Kconfig
new file mode 100644
index 0000000..26bf95a
--- /dev/null
+++ b/drivers/reset/hisilicon/Kconfig
@@ -0,0 +1,5 @@
+config COMMON_RESET_HI6220
+ tristate "Hi6220 Reset Driver"
+ depends on (ARCH_HISI && RESET_CONTROLLER)
+ help
+ Build the Hisilicon Hi6220 reset driver.
diff --git a/drivers/reset/hisilicon/Makefile b/drivers/reset/hisilicon/Makefile
new file mode 100644
index 0000000..c932f86
--- /dev/null
+++ b/drivers/reset/hisilicon/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_COMMON_RESET_HI6220) += hi6220_reset.o
diff --git a/drivers/reset/hisilicon/hi6220_reset.c b/drivers/reset/hisilicon/hi6220_reset.c
new file mode 100644
index 0000000..7787a9b
--- /dev/null
+++ b/drivers/reset/hisilicon/hi6220_reset.c
@@ -0,0 +1,109 @@
+/*
+ * Hisilicon Hi6220 reset controller driver
+ *
+ * Copyright (c) 2015 Hisilicon Limited.
+ *
+ * Author: Feng Chen <puck.chen@hisilicon.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/bitops.h>
+#include <linux/of.h>
+#include <linux/reset-controller.h>
+#include <linux/reset.h>
+#include <linux/platform_device.h>
+
+#define ASSERT_OFFSET 0x300
+#define DEASSERT_OFFSET 0x304
+#define MAX_INDEX 0x509
+
+#define to_reset_data(x) container_of(x, struct hi6220_reset_data, rc_dev)
+
+struct hi6220_reset_data {
+ void __iomem *assert_base;
+ void __iomem *deassert_base;
+ struct reset_controller_dev rc_dev;
+};
+
+static int hi6220_reset_assert(struct reset_controller_dev *rc_dev,
+ unsigned long idx)
+{
+ struct hi6220_reset_data *data = to_reset_data(rc_dev);
+
+ int bank = idx >> 8;
+ int offset = idx & 0xff;
+
+ writel(BIT(offset), data->assert_base + (bank * 0x10));
+
+ return 0;
+}
+
+static int hi6220_reset_deassert(struct reset_controller_dev *rc_dev,
+ unsigned long idx)
+{
+ struct hi6220_reset_data *data = to_reset_data(rc_dev);
+
+ int bank = idx >> 8;
+ int offset = idx & 0xff;
+
+ writel(BIT(offset), data->deassert_base + (bank * 0x10));
+
+ return 0;
+}
+
+static struct reset_control_ops hi6220_reset_ops = {
+ .assert = hi6220_reset_assert,
+ .deassert = hi6220_reset_deassert,
+};
+
+static int hi6220_reset_probe(struct platform_device *pdev)
+{
+ struct hi6220_reset_data *data;
+ struct resource *res;
+ void __iomem *src_base;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ src_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(src_base))
+ return PTR_ERR(src_base);
+
+ data->assert_base = src_base + ASSERT_OFFSET;
+ data->deassert_base = src_base + DEASSERT_OFFSET;
+ data->rc_dev.nr_resets = MAX_INDEX;
+ data->rc_dev.ops = &hi6220_reset_ops;
+ data->rc_dev.of_node = pdev->dev.of_node;
+
+ reset_controller_register(&data->rc_dev);
+
+ return 0;
+}
+
+static const struct of_device_id hi6220_reset_match[] = {
+ { .compatible = "hisilicon,hi6220-sysctrl" },
+ { },
+};
+
+static struct platform_driver hi6220_reset_driver = {
+ .probe = hi6220_reset_probe,
+ .driver = {
+ .name = "reset-hi6220",
+ .of_match_table = hi6220_reset_match,
+ },
+};
+
+static int __init hi6220_reset_init(void)
+{
+ return platform_driver_register(&hi6220_reset_driver);
+}
+
+postcore_initcall(hi6220_reset_init);
diff --git a/drivers/reset/reset-ath79.c b/drivers/reset/reset-ath79.c
index 9aaf646..692fc89 100644
--- a/drivers/reset/reset-ath79.c
+++ b/drivers/reset/reset-ath79.c
@@ -15,13 +15,17 @@
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/reset-controller.h>
+#include <linux/reboot.h>
struct ath79_reset {
struct reset_controller_dev rcdev;
+ struct notifier_block restart_nb;
void __iomem *base;
spinlock_t lock;
};
+#define FULL_CHIP_RESET 24
+
static int ath79_reset_update(struct reset_controller_dev *rcdev,
unsigned long id, bool assert)
{
@@ -72,10 +76,22 @@
.status = ath79_reset_status,
};
+static int ath79_reset_restart_handler(struct notifier_block *nb,
+ unsigned long action, void *data)
+{
+ struct ath79_reset *ath79_reset =
+ container_of(nb, struct ath79_reset, restart_nb);
+
+ ath79_reset_assert(&ath79_reset->rcdev, FULL_CHIP_RESET);
+
+ return NOTIFY_DONE;
+}
+
static int ath79_reset_probe(struct platform_device *pdev)
{
struct ath79_reset *ath79_reset;
struct resource *res;
+ int err;
ath79_reset = devm_kzalloc(&pdev->dev,
sizeof(*ath79_reset), GFP_KERNEL);
@@ -96,13 +112,25 @@
ath79_reset->rcdev.of_reset_n_cells = 1;
ath79_reset->rcdev.nr_resets = 32;
- return reset_controller_register(&ath79_reset->rcdev);
+ err = reset_controller_register(&ath79_reset->rcdev);
+ if (err)
+ return err;
+
+ ath79_reset->restart_nb.notifier_call = ath79_reset_restart_handler;
+ ath79_reset->restart_nb.priority = 128;
+
+ err = register_restart_handler(&ath79_reset->restart_nb);
+ if (err)
+ dev_warn(&pdev->dev, "Failed to register restart handler\n");
+
+ return 0;
}
static int ath79_reset_remove(struct platform_device *pdev)
{
struct ath79_reset *ath79_reset = platform_get_drvdata(pdev);
+ unregister_restart_handler(&ath79_reset->restart_nb);
reset_controller_unregister(&ath79_reset->rcdev);
return 0;
diff --git a/drivers/reset/reset-berlin.c b/drivers/reset/reset-berlin.c
index 3c922d3..970b1ad 100644
--- a/drivers/reset/reset-berlin.c
+++ b/drivers/reset/reset-berlin.c
@@ -87,9 +87,7 @@
priv->rcdev.of_reset_n_cells = 2;
priv->rcdev.of_xlate = berlin_reset_xlate;
- reset_controller_register(&priv->rcdev);
-
- return 0;
+ return reset_controller_register(&priv->rcdev);
}
static const struct of_device_id berlin_reset_dt_match[] = {
diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
index 1a6c5d6..b7d773d 100644
--- a/drivers/reset/reset-socfpga.c
+++ b/drivers/reset/reset-socfpga.c
@@ -133,9 +133,8 @@
data->rcdev.nr_resets = NR_BANKS * BITS_PER_LONG;
data->rcdev.ops = &socfpga_reset_ops;
data->rcdev.of_node = pdev->dev.of_node;
- reset_controller_register(&data->rcdev);
- return 0;
+ return reset_controller_register(&data->rcdev);
}
static int socfpga_reset_remove(struct platform_device *pdev)
diff --git a/drivers/reset/reset-sunxi.c b/drivers/reset/reset-sunxi.c
index 3d95c87..8d41a18 100644
--- a/drivers/reset/reset-sunxi.c
+++ b/drivers/reset/reset-sunxi.c
@@ -108,9 +108,8 @@
data->rcdev.nr_resets = size * 32;
data->rcdev.ops = &sunxi_reset_ops;
data->rcdev.of_node = np;
- reset_controller_register(&data->rcdev);
- return 0;
+ return reset_controller_register(&data->rcdev);
err_alloc:
kfree(data);
@@ -122,7 +121,7 @@
* our system, before we can even think of using a regular device
* driver for it.
*/
-static const struct of_device_id sunxi_early_reset_dt_ids[] __initdata = {
+static const struct of_device_id sunxi_early_reset_dt_ids[] __initconst = {
{ .compatible = "allwinner,sun6i-a31-ahb1-reset", },
{ /* sentinel */ },
};
diff --git a/drivers/reset/reset-zynq.c b/drivers/reset/reset-zynq.c
index 89318a5..c6b3cd8 100644
--- a/drivers/reset/reset-zynq.c
+++ b/drivers/reset/reset-zynq.c
@@ -121,9 +121,8 @@
priv->rcdev.nr_resets = resource_size(res) / 4 * BITS_PER_LONG;
priv->rcdev.ops = &zynq_reset_ops;
priv->rcdev.of_node = pdev->dev.of_node;
- reset_controller_register(&priv->rcdev);
- return 0;
+ return reset_controller_register(&priv->rcdev);
}
static int zynq_reset_remove(struct platform_device *pdev)
diff --git a/drivers/reset/sti/reset-stih407.c b/drivers/reset/sti/reset-stih407.c
index 827eb3d..6fb22af 100644
--- a/drivers/reset/sti/reset-stih407.c
+++ b/drivers/reset/sti/reset-stih407.c
@@ -52,6 +52,7 @@
};
/* Reset Generator control 0/1 */
+#define SYSCFG_5128 0x200
#define SYSCFG_5131 0x20c
#define SYSCFG_5132 0x210
@@ -96,6 +97,10 @@
[STIH407_ERAM_HVA_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 1),
[STIH407_LPM_SOFTRESET] = STIH407_SRST_SBC(SYSCFG_4002, 2),
[STIH407_KEYSCAN_SOFTRESET] = STIH407_SRST_LPM(LPM_SYSCFG_1, 8),
+ [STIH407_ST231_AUD_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 26),
+ [STIH407_ST231_DMU_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 27),
+ [STIH407_ST231_GP0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 28),
+ [STIH407_ST231_GP1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5128, 2),
};
/* PicoPHY reset/control */
diff --git a/drivers/reset/sti/reset-syscfg.c b/drivers/reset/sti/reset-syscfg.c
index a145cc06..1600cc7 100644
--- a/drivers/reset/sti/reset-syscfg.c
+++ b/drivers/reset/sti/reset-syscfg.c
@@ -103,17 +103,42 @@
static int syscfg_reset_dev(struct reset_controller_dev *rcdev,
unsigned long idx)
{
- int err = syscfg_reset_assert(rcdev, idx);
+ int err;
+
+ err = syscfg_reset_assert(rcdev, idx);
if (err)
return err;
return syscfg_reset_deassert(rcdev, idx);
}
+static int syscfg_reset_status(struct reset_controller_dev *rcdev,
+ unsigned long idx)
+{
+ struct syscfg_reset_controller *rst = to_syscfg_reset_controller(rcdev);
+ const struct syscfg_reset_channel *ch;
+ u32 ret_val = 0;
+ int err;
+
+ if (idx >= rcdev->nr_resets)
+ return -EINVAL;
+
+ ch = &rst->channels[idx];
+ if (ch->ack)
+ err = regmap_field_read(ch->ack, &ret_val);
+ else
+ err = regmap_field_read(ch->reset, &ret_val);
+ if (err)
+ return err;
+
+ return rst->active_low ? !ret_val : !!ret_val;
+}
+
static struct reset_control_ops syscfg_reset_ops = {
.reset = syscfg_reset_dev,
.assert = syscfg_reset_assert,
.deassert = syscfg_reset_deassert,
+ .status = syscfg_reset_status,
};
static int syscfg_reset_controller_register(struct device *dev,
diff --git a/drivers/soc/Kconfig b/drivers/soc/Kconfig
index ad0df75..fb2b393 100644
--- a/drivers/soc/Kconfig
+++ b/drivers/soc/Kconfig
@@ -1,5 +1,6 @@
menu "SOC (System On Chip) specific Drivers"
+source "drivers/soc/bcm/Kconfig"
source "drivers/soc/brcmstb/Kconfig"
source "drivers/soc/fsl/qe/Kconfig"
source "drivers/soc/mediatek/Kconfig"
diff --git a/drivers/soc/Makefile b/drivers/soc/Makefile
index 9b1c2e8..2afdc74 100644
--- a/drivers/soc/Makefile
+++ b/drivers/soc/Makefile
@@ -2,6 +2,7 @@
# Makefile for the Linux Kernel SOC specific device drivers.
#
+obj-y += bcm/
obj-$(CONFIG_SOC_BRCMSTB) += brcmstb/
obj-$(CONFIG_ARCH_DOVE) += dove/
obj-$(CONFIG_MACH_DOVE) += dove/
diff --git a/drivers/soc/bcm/Kconfig b/drivers/soc/bcm/Kconfig
new file mode 100644
index 0000000..3066ede
--- /dev/null
+++ b/drivers/soc/bcm/Kconfig
@@ -0,0 +1,9 @@
+config RASPBERRYPI_POWER
+ bool "Raspberry Pi power domain driver"
+ depends on ARCH_BCM2835 || COMPILE_TEST
+ depends on RASPBERRYPI_FIRMWARE=y
+ select PM_GENERIC_DOMAINS if PM
+ select PM_GENERIC_DOMAINS_OF if PM
+ help
+ This enables support for the RPi power domains which can be enabled
+ or disabled via the RPi firmware.
diff --git a/drivers/soc/bcm/Makefile b/drivers/soc/bcm/Makefile
new file mode 100644
index 0000000..63aa3eb
--- /dev/null
+++ b/drivers/soc/bcm/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_RASPBERRYPI_POWER) += raspberrypi-power.o
diff --git a/drivers/soc/bcm/raspberrypi-power.c b/drivers/soc/bcm/raspberrypi-power.c
new file mode 100644
index 0000000..fe96a8b
--- /dev/null
+++ b/drivers/soc/bcm/raspberrypi-power.c
@@ -0,0 +1,247 @@
+/* (C) 2015 Pengutronix, Alexander Aring <aar@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Authors:
+ * Alexander Aring <aar@pengutronix.de>
+ * Eric Anholt <eric@anholt.net>
+ */
+
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <dt-bindings/power/raspberrypi-power.h>
+#include <soc/bcm2835/raspberrypi-firmware.h>
+
+/*
+ * Firmware indices for the old power domains interface. Only a few
+ * of them were actually implemented.
+ */
+#define RPI_OLD_POWER_DOMAIN_USB 3
+#define RPI_OLD_POWER_DOMAIN_V3D 10
+
+struct rpi_power_domain {
+ u32 domain;
+ bool enabled;
+ bool old_interface;
+ struct generic_pm_domain base;
+ struct rpi_firmware *fw;
+};
+
+struct rpi_power_domains {
+ bool has_new_interface;
+ struct genpd_onecell_data xlate;
+ struct rpi_firmware *fw;
+ struct rpi_power_domain domains[RPI_POWER_DOMAIN_COUNT];
+};
+
+/*
+ * Packet definition used by RPI_FIRMWARE_SET_POWER_STATE and
+ * RPI_FIRMWARE_SET_DOMAIN_STATE
+ */
+struct rpi_power_domain_packet {
+ u32 domain;
+ u32 on;
+} __packet;
+
+/*
+ * Asks the firmware to enable or disable power on a specific power
+ * domain.
+ */
+static int rpi_firmware_set_power(struct rpi_power_domain *rpi_domain, bool on)
+{
+ struct rpi_power_domain_packet packet;
+
+ packet.domain = rpi_domain->domain;
+ packet.on = on;
+ return rpi_firmware_property(rpi_domain->fw,
+ rpi_domain->old_interface ?
+ RPI_FIRMWARE_SET_POWER_STATE :
+ RPI_FIRMWARE_SET_DOMAIN_STATE,
+ &packet, sizeof(packet));
+}
+
+static int rpi_domain_off(struct generic_pm_domain *domain)
+{
+ struct rpi_power_domain *rpi_domain =
+ container_of(domain, struct rpi_power_domain, base);
+
+ return rpi_firmware_set_power(rpi_domain, false);
+}
+
+static int rpi_domain_on(struct generic_pm_domain *domain)
+{
+ struct rpi_power_domain *rpi_domain =
+ container_of(domain, struct rpi_power_domain, base);
+
+ return rpi_firmware_set_power(rpi_domain, true);
+}
+
+static void rpi_common_init_power_domain(struct rpi_power_domains *rpi_domains,
+ int xlate_index, const char *name)
+{
+ struct rpi_power_domain *dom = &rpi_domains->domains[xlate_index];
+
+ dom->fw = rpi_domains->fw;
+
+ dom->base.name = name;
+ dom->base.power_on = rpi_domain_on;
+ dom->base.power_off = rpi_domain_off;
+
+ /*
+ * Treat all power domains as off at boot.
+ *
+ * The firmware itself may be keeping some domains on, but
+ * from Linux's perspective all we control is the refcounts
+ * that we give to the firmware, and we can't ask the firmware
+ * to turn off something that we haven't ourselves turned on.
+ */
+ pm_genpd_init(&dom->base, NULL, true);
+
+ rpi_domains->xlate.domains[xlate_index] = &dom->base;
+}
+
+static void rpi_init_power_domain(struct rpi_power_domains *rpi_domains,
+ int xlate_index, const char *name)
+{
+ struct rpi_power_domain *dom = &rpi_domains->domains[xlate_index];
+
+ if (!rpi_domains->has_new_interface)
+ return;
+
+ /* The DT binding index is the firmware's domain index minus one. */
+ dom->domain = xlate_index + 1;
+
+ rpi_common_init_power_domain(rpi_domains, xlate_index, name);
+}
+
+static void rpi_init_old_power_domain(struct rpi_power_domains *rpi_domains,
+ int xlate_index, int domain,
+ const char *name)
+{
+ struct rpi_power_domain *dom = &rpi_domains->domains[xlate_index];
+
+ dom->old_interface = true;
+ dom->domain = domain;
+
+ rpi_common_init_power_domain(rpi_domains, xlate_index, name);
+}
+
+/*
+ * Detects whether the firmware supports the new power domains interface.
+ *
+ * The firmware doesn't actually return an error on an unknown tag,
+ * and just skips over it, so we do the detection by putting an
+ * unexpected value in the return field and checking if it was
+ * unchanged.
+ */
+static bool
+rpi_has_new_domain_support(struct rpi_power_domains *rpi_domains)
+{
+ struct rpi_power_domain_packet packet;
+ int ret;
+
+ packet.domain = RPI_POWER_DOMAIN_ARM;
+ packet.on = ~0;
+
+ ret = rpi_firmware_property(rpi_domains->fw,
+ RPI_FIRMWARE_GET_DOMAIN_STATE,
+ &packet, sizeof(packet));
+
+ return ret == 0 && packet.on != ~0;
+}
+
+static int rpi_power_probe(struct platform_device *pdev)
+{
+ struct device_node *fw_np;
+ struct device *dev = &pdev->dev;
+ struct rpi_power_domains *rpi_domains;
+
+ rpi_domains = devm_kzalloc(dev, sizeof(*rpi_domains), GFP_KERNEL);
+ if (!rpi_domains)
+ return -ENOMEM;
+
+ rpi_domains->xlate.domains =
+ devm_kzalloc(dev, sizeof(*rpi_domains->xlate.domains) *
+ RPI_POWER_DOMAIN_COUNT, GFP_KERNEL);
+ if (!rpi_domains->xlate.domains)
+ return -ENOMEM;
+
+ rpi_domains->xlate.num_domains = RPI_POWER_DOMAIN_COUNT;
+
+ fw_np = of_parse_phandle(pdev->dev.of_node, "firmware", 0);
+ if (!fw_np) {
+ dev_err(&pdev->dev, "no firmware node\n");
+ return -ENODEV;
+ }
+
+ rpi_domains->fw = rpi_firmware_get(fw_np);
+ of_node_put(fw_np);
+ if (!rpi_domains->fw)
+ return -EPROBE_DEFER;
+
+ rpi_domains->has_new_interface =
+ rpi_has_new_domain_support(rpi_domains);
+
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_I2C0, "I2C0");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_I2C1, "I2C1");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_I2C2, "I2C2");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_VIDEO_SCALER,
+ "VIDEO_SCALER");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_VPU1, "VPU1");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_HDMI, "HDMI");
+
+ /*
+ * Use the old firmware interface for USB power, so that we
+ * can turn it on even if the firmware hasn't been updated.
+ */
+ rpi_init_old_power_domain(rpi_domains, RPI_POWER_DOMAIN_USB,
+ RPI_OLD_POWER_DOMAIN_USB, "USB");
+
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_VEC, "VEC");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_JPEG, "JPEG");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_H264, "H264");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_V3D, "V3D");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_ISP, "ISP");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_UNICAM0, "UNICAM0");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_UNICAM1, "UNICAM1");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_CCP2RX, "CCP2RX");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_CSI2, "CSI2");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_CPI, "CPI");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_DSI0, "DSI0");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_DSI1, "DSI1");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_TRANSPOSER,
+ "TRANSPOSER");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_CCP2TX, "CCP2TX");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_CDP, "CDP");
+ rpi_init_power_domain(rpi_domains, RPI_POWER_DOMAIN_ARM, "ARM");
+
+ of_genpd_add_provider_onecell(dev->of_node, &rpi_domains->xlate);
+
+ platform_set_drvdata(pdev, rpi_domains);
+
+ return 0;
+}
+
+static const struct of_device_id rpi_power_of_match[] = {
+ { .compatible = "raspberrypi,bcm2835-power", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, rpi_power_of_match);
+
+static struct platform_driver rpi_power_driver = {
+ .driver = {
+ .name = "raspberrypi-power",
+ .of_match_table = rpi_power_of_match,
+ },
+ .probe = rpi_power_probe,
+};
+builtin_platform_driver(rpi_power_driver);
+
+MODULE_AUTHOR("Alexander Aring <aar@pengutronix.de>");
+MODULE_AUTHOR("Eric Anholt <eric@anholt.net>");
+MODULE_DESCRIPTION("Raspberry Pi power domain driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/soc/mediatek/mtk-scpsys.c b/drivers/soc/mediatek/mtk-scpsys.c
index 4d4203c..0221387 100644
--- a/drivers/soc/mediatek/mtk-scpsys.c
+++ b/drivers/soc/mediatek/mtk-scpsys.c
@@ -15,12 +15,13 @@
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/mfd/syscon.h>
-#include <linux/module.h>
+#include <linux/init.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/pm_domain.h>
#include <linux/regmap.h>
#include <linux/soc/mediatek/infracfg.h>
+#include <linux/regulator/consumer.h>
#include <dt-bindings/power/mt8173-power.h>
#define SPM_VDE_PWR_CON 0x0210
@@ -179,6 +180,7 @@
u32 sram_pdn_ack_bits;
u32 bus_prot_mask;
bool active_wakeup;
+ struct regulator *supply;
};
struct scp {
@@ -221,6 +223,12 @@
int ret;
int i;
+ if (scpd->supply) {
+ ret = regulator_enable(scpd->supply);
+ if (ret)
+ return ret;
+ }
+
for (i = 0; i < MAX_CLKS && scpd->clk[i]; i++) {
ret = clk_prepare_enable(scpd->clk[i]);
if (ret) {
@@ -299,6 +307,9 @@
clk_disable_unprepare(scpd->clk[i]);
}
err_clk:
+ if (scpd->supply)
+ regulator_disable(scpd->supply);
+
dev_err(scp->dev, "Failed to power on domain %s\n", genpd->name);
return ret;
@@ -379,6 +390,9 @@
for (i = 0; i < MAX_CLKS && scpd->clk[i]; i++)
clk_disable_unprepare(scpd->clk[i]);
+ if (scpd->supply)
+ regulator_disable(scpd->supply);
+
return 0;
out:
@@ -448,6 +462,19 @@
return PTR_ERR(scp->infracfg);
}
+ for (i = 0; i < NUM_DOMAINS; i++) {
+ struct scp_domain *scpd = &scp->domains[i];
+ const struct scp_domain_data *data = &scp_domain_data[i];
+
+ scpd->supply = devm_regulator_get_optional(&pdev->dev, data->name);
+ if (IS_ERR(scpd->supply)) {
+ if (PTR_ERR(scpd->supply) == -ENODEV)
+ scpd->supply = NULL;
+ else
+ return PTR_ERR(scpd->supply);
+ }
+ }
+
pd_data->num_domains = NUM_DOMAINS;
for (i = 0; i < NUM_DOMAINS; i++) {
@@ -521,5 +548,4 @@
.of_match_table = of_match_ptr(of_scpsys_match_tbl),
},
};
-
-module_platform_driver_probe(scpsys_drv, scpsys_probe);
+builtin_platform_driver_probe(scpsys_drv, scpsys_probe);
diff --git a/drivers/soc/qcom/Kconfig b/drivers/soc/qcom/Kconfig
index eec7614..461b387 100644
--- a/drivers/soc/qcom/Kconfig
+++ b/drivers/soc/qcom/Kconfig
@@ -13,6 +13,7 @@
config QCOM_PM
bool "Qualcomm Power Management"
depends on ARCH_QCOM && !ARM64
+ select ARM_CPU_SUSPEND
select QCOM_SCM
help
QCOM Platform specific power driver to manage cores and L2 low power
@@ -49,3 +50,29 @@
Say M here if you want to include support for the Qualcomm RPM as a
module. This will build a module called "qcom-smd-rpm".
+
+config QCOM_SMEM_STATE
+ bool
+
+config QCOM_SMP2P
+ tristate "Qualcomm Shared Memory Point to Point support"
+ depends on QCOM_SMEM
+ select QCOM_SMEM_STATE
+ help
+ Say yes here to support the Qualcomm Shared Memory Point to Point
+ protocol.
+
+config QCOM_SMSM
+ tristate "Qualcomm Shared Memory State Machine"
+ depends on QCOM_SMEM
+ select QCOM_SMEM_STATE
+ help
+ Say yes here to support the Qualcomm Shared Memory State Machine.
+ The state machine is represented by bits in shared memory.
+
+config QCOM_WCNSS_CTRL
+ tristate "Qualcomm WCNSS control driver"
+ depends on QCOM_SMD
+ help
+ Client driver for the WCNSS_CTRL SMD channel, used to download nv
+ firmware to a newly booted WCNSS chip.
diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile
index 10a93d1..fdd664e 100644
--- a/drivers/soc/qcom/Makefile
+++ b/drivers/soc/qcom/Makefile
@@ -3,3 +3,7 @@
obj-$(CONFIG_QCOM_SMD) += smd.o
obj-$(CONFIG_QCOM_SMD_RPM) += smd-rpm.o
obj-$(CONFIG_QCOM_SMEM) += smem.o
+obj-$(CONFIG_QCOM_SMEM_STATE) += smem_state.o
+obj-$(CONFIG_QCOM_SMP2P) += smp2p.o
+obj-$(CONFIG_QCOM_SMSM) += smsm.o
+obj-$(CONFIG_QCOM_WCNSS_CTRL) += wcnss_ctrl.o
diff --git a/drivers/soc/qcom/smd-rpm.c b/drivers/soc/qcom/smd-rpm.c
index 2969321..731fa06 100644
--- a/drivers/soc/qcom/smd-rpm.c
+++ b/drivers/soc/qcom/smd-rpm.c
@@ -219,6 +219,8 @@
}
static const struct of_device_id qcom_smd_rpm_of_match[] = {
+ { .compatible = "qcom,rpm-apq8084" },
+ { .compatible = "qcom,rpm-msm8916" },
{ .compatible = "qcom,rpm-msm8974" },
{}
};
diff --git a/drivers/soc/qcom/smem_state.c b/drivers/soc/qcom/smem_state.c
new file mode 100644
index 0000000..54261de
--- /dev/null
+++ b/drivers/soc/qcom/smem_state.c
@@ -0,0 +1,201 @@
+/*
+ * Copyright (c) 2015, Sony Mobile Communications Inc.
+ * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/device.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/slab.h>
+#include <linux/soc/qcom/smem_state.h>
+
+static LIST_HEAD(smem_states);
+static DEFINE_MUTEX(list_lock);
+
+/**
+ * struct qcom_smem_state - state context
+ * @refcount: refcount for the state
+ * @orphan: boolean indicator that this state has been unregistered
+ * @list: entry in smem_states list
+ * @of_node: of_node to use for matching the state in DT
+ * @priv: implementation private data
+ * @ops: ops for the state
+ */
+struct qcom_smem_state {
+ struct kref refcount;
+ bool orphan;
+
+ struct list_head list;
+ struct device_node *of_node;
+
+ void *priv;
+
+ struct qcom_smem_state_ops ops;
+};
+
+/**
+ * qcom_smem_state_update_bits() - update the masked bits in state with value
+ * @state: state handle acquired by calling qcom_smem_state_get()
+ * @mask: bit mask for the change
+ * @value: new value for the masked bits
+ *
+ * Returns 0 on success, otherwise negative errno.
+ */
+int qcom_smem_state_update_bits(struct qcom_smem_state *state,
+ u32 mask,
+ u32 value)
+{
+ if (state->orphan)
+ return -ENXIO;
+
+ if (!state->ops.update_bits)
+ return -ENOTSUPP;
+
+ return state->ops.update_bits(state->priv, mask, value);
+}
+EXPORT_SYMBOL_GPL(qcom_smem_state_update_bits);
+
+static struct qcom_smem_state *of_node_to_state(struct device_node *np)
+{
+ struct qcom_smem_state *state;
+
+ mutex_lock(&list_lock);
+
+ list_for_each_entry(state, &smem_states, list) {
+ if (state->of_node == np) {
+ kref_get(&state->refcount);
+ goto unlock;
+ }
+ }
+ state = ERR_PTR(-EPROBE_DEFER);
+
+unlock:
+ mutex_unlock(&list_lock);
+
+ return state;
+}
+
+/**
+ * qcom_smem_state_get() - acquire handle to a state
+ * @dev: client device pointer
+ * @con_id: name of the state to lookup
+ * @bit: flags from the state reference, indicating which bit's affected
+ *
+ * Returns handle to the state, or ERR_PTR(). qcom_smem_state_put() must be
+ * called to release the returned state handle.
+ */
+struct qcom_smem_state *qcom_smem_state_get(struct device *dev,
+ const char *con_id,
+ unsigned *bit)
+{
+ struct qcom_smem_state *state;
+ struct of_phandle_args args;
+ int index = 0;
+ int ret;
+
+ if (con_id) {
+ index = of_property_match_string(dev->of_node,
+ "qcom,state-names",
+ con_id);
+ if (index < 0) {
+ dev_err(dev, "missing qcom,state-names\n");
+ return ERR_PTR(index);
+ }
+ }
+
+ ret = of_parse_phandle_with_args(dev->of_node,
+ "qcom,state",
+ "#qcom,state-cells",
+ index,
+ &args);
+ if (ret) {
+ dev_err(dev, "failed to parse qcom,state property\n");
+ return ERR_PTR(ret);
+ }
+
+ if (args.args_count != 1) {
+ dev_err(dev, "invalid #qcom,state-cells\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ state = of_node_to_state(args.np);
+ if (IS_ERR(state))
+ goto put;
+
+ *bit = args.args[0];
+
+put:
+ of_node_put(args.np);
+ return state;
+}
+EXPORT_SYMBOL_GPL(qcom_smem_state_get);
+
+static void qcom_smem_state_release(struct kref *ref)
+{
+ struct qcom_smem_state *state = container_of(ref, struct qcom_smem_state, refcount);
+
+ list_del(&state->list);
+ kfree(state);
+}
+
+/**
+ * qcom_smem_state_put() - release state handle
+ * @state: state handle to be released
+ */
+void qcom_smem_state_put(struct qcom_smem_state *state)
+{
+ mutex_lock(&list_lock);
+ kref_put(&state->refcount, qcom_smem_state_release);
+ mutex_unlock(&list_lock);
+}
+EXPORT_SYMBOL_GPL(qcom_smem_state_put);
+
+/**
+ * qcom_smem_state_register() - register a new state
+ * @of_node: of_node used for matching client lookups
+ * @ops: implementation ops
+ * @priv: implementation specific private data
+ */
+struct qcom_smem_state *qcom_smem_state_register(struct device_node *of_node,
+ const struct qcom_smem_state_ops *ops,
+ void *priv)
+{
+ struct qcom_smem_state *state;
+
+ state = kzalloc(sizeof(*state), GFP_KERNEL);
+ if (!state)
+ return ERR_PTR(-ENOMEM);
+
+ kref_init(&state->refcount);
+
+ state->of_node = of_node;
+ state->ops = *ops;
+ state->priv = priv;
+
+ mutex_lock(&list_lock);
+ list_add(&state->list, &smem_states);
+ mutex_unlock(&list_lock);
+
+ return state;
+}
+EXPORT_SYMBOL_GPL(qcom_smem_state_register);
+
+/**
+ * qcom_smem_state_unregister() - unregister a registered state
+ * @state: state handle to be unregistered
+ */
+void qcom_smem_state_unregister(struct qcom_smem_state *state)
+{
+ state->orphan = true;
+ qcom_smem_state_put(state);
+}
+EXPORT_SYMBOL_GPL(qcom_smem_state_unregister);
diff --git a/drivers/soc/qcom/smp2p.c b/drivers/soc/qcom/smp2p.c
new file mode 100644
index 0000000..f1eed7f
--- /dev/null
+++ b/drivers/soc/qcom/smp2p.c
@@ -0,0 +1,578 @@
+/*
+ * Copyright (c) 2015, Sony Mobile Communications AB.
+ * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/soc/qcom/smem.h>
+#include <linux/soc/qcom/smem_state.h>
+#include <linux/spinlock.h>
+
+/*
+ * The Shared Memory Point to Point (SMP2P) protocol facilitates communication
+ * of a single 32-bit value between two processors. Each value has a single
+ * writer (the local side) and a single reader (the remote side). Values are
+ * uniquely identified in the system by the directed edge (local processor ID
+ * to remote processor ID) and a string identifier.
+ *
+ * Each processor is responsible for creating the outgoing SMEM items and each
+ * item is writable by the local processor and readable by the remote
+ * processor. By using two separate SMEM items that are single-reader and
+ * single-writer, SMP2P does not require any remote locking mechanisms.
+ *
+ * The driver uses the Linux GPIO and interrupt framework to expose a virtual
+ * GPIO for each outbound entry and a virtual interrupt controller for each
+ * inbound entry.
+ */
+
+#define SMP2P_MAX_ENTRY 16
+#define SMP2P_MAX_ENTRY_NAME 16
+
+#define SMP2P_FEATURE_SSR_ACK 0x1
+
+#define SMP2P_MAGIC 0x504d5324
+
+/**
+ * struct smp2p_smem_item - in memory communication structure
+ * @magic: magic number
+ * @version: version - must be 1
+ * @features: features flag - currently unused
+ * @local_pid: processor id of sending end
+ * @remote_pid: processor id of receiving end
+ * @total_entries: number of entries - always SMP2P_MAX_ENTRY
+ * @valid_entries: number of allocated entries
+ * @flags:
+ * @entries: individual communication entries
+ * @name: name of the entry
+ * @value: content of the entry
+ */
+struct smp2p_smem_item {
+ u32 magic;
+ u8 version;
+ unsigned features:24;
+ u16 local_pid;
+ u16 remote_pid;
+ u16 total_entries;
+ u16 valid_entries;
+ u32 flags;
+
+ struct {
+ u8 name[SMP2P_MAX_ENTRY_NAME];
+ u32 value;
+ } entries[SMP2P_MAX_ENTRY];
+} __packed;
+
+/**
+ * struct smp2p_entry - driver context matching one entry
+ * @node: list entry to keep track of allocated entries
+ * @smp2p: reference to the device driver context
+ * @name: name of the entry, to match against smp2p_smem_item
+ * @value: pointer to smp2p_smem_item entry value
+ * @last_value: last handled value
+ * @domain: irq_domain for inbound entries
+ * @irq_enabled:bitmap to track enabled irq bits
+ * @irq_rising: bitmap to mark irq bits for rising detection
+ * @irq_falling:bitmap to mark irq bits for falling detection
+ * @state: smem state handle
+ * @lock: spinlock to protect read-modify-write of the value
+ */
+struct smp2p_entry {
+ struct list_head node;
+ struct qcom_smp2p *smp2p;
+
+ const char *name;
+ u32 *value;
+ u32 last_value;
+
+ struct irq_domain *domain;
+ DECLARE_BITMAP(irq_enabled, 32);
+ DECLARE_BITMAP(irq_rising, 32);
+ DECLARE_BITMAP(irq_falling, 32);
+
+ struct qcom_smem_state *state;
+
+ spinlock_t lock;
+};
+
+#define SMP2P_INBOUND 0
+#define SMP2P_OUTBOUND 1
+
+/**
+ * struct qcom_smp2p - device driver context
+ * @dev: device driver handle
+ * @in: pointer to the inbound smem item
+ * @smem_items: ids of the two smem items
+ * @valid_entries: already scanned inbound entries
+ * @local_pid: processor id of the inbound edge
+ * @remote_pid: processor id of the outbound edge
+ * @ipc_regmap: regmap for the outbound ipc
+ * @ipc_offset: offset within the regmap
+ * @ipc_bit: bit in regmap@offset to kick to signal remote processor
+ * @inbound: list of inbound entries
+ * @outbound: list of outbound entries
+ */
+struct qcom_smp2p {
+ struct device *dev;
+
+ struct smp2p_smem_item *in;
+ struct smp2p_smem_item *out;
+
+ unsigned smem_items[SMP2P_OUTBOUND + 1];
+
+ unsigned valid_entries;
+
+ unsigned local_pid;
+ unsigned remote_pid;
+
+ struct regmap *ipc_regmap;
+ int ipc_offset;
+ int ipc_bit;
+
+ struct list_head inbound;
+ struct list_head outbound;
+};
+
+static void qcom_smp2p_kick(struct qcom_smp2p *smp2p)
+{
+ /* Make sure any updated data is written before the kick */
+ wmb();
+ regmap_write(smp2p->ipc_regmap, smp2p->ipc_offset, BIT(smp2p->ipc_bit));
+}
+
+/**
+ * qcom_smp2p_intr() - interrupt handler for incoming notifications
+ * @irq: unused
+ * @data: smp2p driver context
+ *
+ * Handle notifications from the remote side to handle newly allocated entries
+ * or any changes to the state bits of existing entries.
+ */
+static irqreturn_t qcom_smp2p_intr(int irq, void *data)
+{
+ struct smp2p_smem_item *in;
+ struct smp2p_entry *entry;
+ struct qcom_smp2p *smp2p = data;
+ unsigned smem_id = smp2p->smem_items[SMP2P_INBOUND];
+ unsigned pid = smp2p->remote_pid;
+ size_t size;
+ int irq_pin;
+ u32 status;
+ char buf[SMP2P_MAX_ENTRY_NAME];
+ u32 val;
+ int i;
+
+ in = smp2p->in;
+
+ /* Acquire smem item, if not already found */
+ if (!in) {
+ in = qcom_smem_get(pid, smem_id, &size);
+ if (IS_ERR(in)) {
+ dev_err(smp2p->dev,
+ "Unable to acquire remote smp2p item\n");
+ return IRQ_HANDLED;
+ }
+
+ smp2p->in = in;
+ }
+
+ /* Match newly created entries */
+ for (i = smp2p->valid_entries; i < in->valid_entries; i++) {
+ list_for_each_entry(entry, &smp2p->inbound, node) {
+ memcpy_fromio(buf, in->entries[i].name, sizeof(buf));
+ if (!strcmp(buf, entry->name)) {
+ entry->value = &in->entries[i].value;
+ break;
+ }
+ }
+ }
+ smp2p->valid_entries = i;
+
+ /* Fire interrupts based on any value changes */
+ list_for_each_entry(entry, &smp2p->inbound, node) {
+ /* Ignore entries not yet allocated by the remote side */
+ if (!entry->value)
+ continue;
+
+ val = readl(entry->value);
+
+ status = val ^ entry->last_value;
+ entry->last_value = val;
+
+ /* No changes of this entry? */
+ if (!status)
+ continue;
+
+ for_each_set_bit(i, entry->irq_enabled, 32) {
+ if (!(status & BIT(i)))
+ continue;
+
+ if ((val & BIT(i) && test_bit(i, entry->irq_rising)) ||
+ (!(val & BIT(i)) && test_bit(i, entry->irq_falling))) {
+ irq_pin = irq_find_mapping(entry->domain, i);
+ handle_nested_irq(irq_pin);
+ }
+ }
+ }
+
+ return IRQ_HANDLED;
+}
+
+static void smp2p_mask_irq(struct irq_data *irqd)
+{
+ struct smp2p_entry *entry = irq_data_get_irq_chip_data(irqd);
+ irq_hw_number_t irq = irqd_to_hwirq(irqd);
+
+ clear_bit(irq, entry->irq_enabled);
+}
+
+static void smp2p_unmask_irq(struct irq_data *irqd)
+{
+ struct smp2p_entry *entry = irq_data_get_irq_chip_data(irqd);
+ irq_hw_number_t irq = irqd_to_hwirq(irqd);
+
+ set_bit(irq, entry->irq_enabled);
+}
+
+static int smp2p_set_irq_type(struct irq_data *irqd, unsigned int type)
+{
+ struct smp2p_entry *entry = irq_data_get_irq_chip_data(irqd);
+ irq_hw_number_t irq = irqd_to_hwirq(irqd);
+
+ if (!(type & IRQ_TYPE_EDGE_BOTH))
+ return -EINVAL;
+
+ if (type & IRQ_TYPE_EDGE_RISING)
+ set_bit(irq, entry->irq_rising);
+ else
+ clear_bit(irq, entry->irq_rising);
+
+ if (type & IRQ_TYPE_EDGE_FALLING)
+ set_bit(irq, entry->irq_falling);
+ else
+ clear_bit(irq, entry->irq_falling);
+
+ return 0;
+}
+
+static struct irq_chip smp2p_irq_chip = {
+ .name = "smp2p",
+ .irq_mask = smp2p_mask_irq,
+ .irq_unmask = smp2p_unmask_irq,
+ .irq_set_type = smp2p_set_irq_type,
+};
+
+static int smp2p_irq_map(struct irq_domain *d,
+ unsigned int irq,
+ irq_hw_number_t hw)
+{
+ struct smp2p_entry *entry = d->host_data;
+
+ irq_set_chip_and_handler(irq, &smp2p_irq_chip, handle_level_irq);
+ irq_set_chip_data(irq, entry);
+ irq_set_nested_thread(irq, 1);
+ irq_set_noprobe(irq);
+
+ return 0;
+}
+
+static const struct irq_domain_ops smp2p_irq_ops = {
+ .map = smp2p_irq_map,
+ .xlate = irq_domain_xlate_twocell,
+};
+
+static int qcom_smp2p_inbound_entry(struct qcom_smp2p *smp2p,
+ struct smp2p_entry *entry,
+ struct device_node *node)
+{
+ entry->domain = irq_domain_add_linear(node, 32, &smp2p_irq_ops, entry);
+ if (!entry->domain) {
+ dev_err(smp2p->dev, "failed to add irq_domain\n");
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static int smp2p_update_bits(void *data, u32 mask, u32 value)
+{
+ struct smp2p_entry *entry = data;
+ u32 orig;
+ u32 val;
+
+ spin_lock(&entry->lock);
+ val = orig = readl(entry->value);
+ val &= ~mask;
+ val |= value;
+ writel(val, entry->value);
+ spin_unlock(&entry->lock);
+
+ if (val != orig)
+ qcom_smp2p_kick(entry->smp2p);
+
+ return 0;
+}
+
+static const struct qcom_smem_state_ops smp2p_state_ops = {
+ .update_bits = smp2p_update_bits,
+};
+
+static int qcom_smp2p_outbound_entry(struct qcom_smp2p *smp2p,
+ struct smp2p_entry *entry,
+ struct device_node *node)
+{
+ struct smp2p_smem_item *out = smp2p->out;
+ char buf[SMP2P_MAX_ENTRY_NAME] = {};
+
+ /* Allocate an entry from the smem item */
+ strlcpy(buf, entry->name, SMP2P_MAX_ENTRY_NAME);
+ memcpy_toio(out->entries[out->valid_entries].name, buf, SMP2P_MAX_ENTRY_NAME);
+ out->valid_entries++;
+
+ /* Make the logical entry reference the physical value */
+ entry->value = &out->entries[out->valid_entries].value;
+
+ entry->state = qcom_smem_state_register(node, &smp2p_state_ops, entry);
+ if (IS_ERR(entry->state)) {
+ dev_err(smp2p->dev, "failed to register qcom_smem_state\n");
+ return PTR_ERR(entry->state);
+ }
+
+ return 0;
+}
+
+static int qcom_smp2p_alloc_outbound_item(struct qcom_smp2p *smp2p)
+{
+ struct smp2p_smem_item *out;
+ unsigned smem_id = smp2p->smem_items[SMP2P_OUTBOUND];
+ unsigned pid = smp2p->remote_pid;
+ int ret;
+
+ ret = qcom_smem_alloc(pid, smem_id, sizeof(*out));
+ if (ret < 0 && ret != -EEXIST) {
+ if (ret != -EPROBE_DEFER)
+ dev_err(smp2p->dev,
+ "unable to allocate local smp2p item\n");
+ return ret;
+ }
+
+ out = qcom_smem_get(pid, smem_id, NULL);
+ if (IS_ERR(out)) {
+ dev_err(smp2p->dev, "Unable to acquire local smp2p item\n");
+ return PTR_ERR(out);
+ }
+
+ memset(out, 0, sizeof(*out));
+ out->magic = SMP2P_MAGIC;
+ out->local_pid = smp2p->local_pid;
+ out->remote_pid = smp2p->remote_pid;
+ out->total_entries = SMP2P_MAX_ENTRY;
+ out->valid_entries = 0;
+
+ /*
+ * Make sure the rest of the header is written before we validate the
+ * item by writing a valid version number.
+ */
+ wmb();
+ out->version = 1;
+
+ qcom_smp2p_kick(smp2p);
+
+ smp2p->out = out;
+
+ return 0;
+}
+
+static int smp2p_parse_ipc(struct qcom_smp2p *smp2p)
+{
+ struct device_node *syscon;
+ struct device *dev = smp2p->dev;
+ const char *key;
+ int ret;
+
+ syscon = of_parse_phandle(dev->of_node, "qcom,ipc", 0);
+ if (!syscon) {
+ dev_err(dev, "no qcom,ipc node\n");
+ return -ENODEV;
+ }
+
+ smp2p->ipc_regmap = syscon_node_to_regmap(syscon);
+ if (IS_ERR(smp2p->ipc_regmap))
+ return PTR_ERR(smp2p->ipc_regmap);
+
+ key = "qcom,ipc";
+ ret = of_property_read_u32_index(dev->of_node, key, 1, &smp2p->ipc_offset);
+ if (ret < 0) {
+ dev_err(dev, "no offset in %s\n", key);
+ return -EINVAL;
+ }
+
+ ret = of_property_read_u32_index(dev->of_node, key, 2, &smp2p->ipc_bit);
+ if (ret < 0) {
+ dev_err(dev, "no bit in %s\n", key);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int qcom_smp2p_probe(struct platform_device *pdev)
+{
+ struct smp2p_entry *entry;
+ struct device_node *node;
+ struct qcom_smp2p *smp2p;
+ const char *key;
+ int irq;
+ int ret;
+
+ smp2p = devm_kzalloc(&pdev->dev, sizeof(*smp2p), GFP_KERNEL);
+ if (!smp2p)
+ return -ENOMEM;
+
+ smp2p->dev = &pdev->dev;
+ INIT_LIST_HEAD(&smp2p->inbound);
+ INIT_LIST_HEAD(&smp2p->outbound);
+
+ platform_set_drvdata(pdev, smp2p);
+
+ ret = smp2p_parse_ipc(smp2p);
+ if (ret)
+ return ret;
+
+ key = "qcom,smem";
+ ret = of_property_read_u32_array(pdev->dev.of_node, key,
+ smp2p->smem_items, 2);
+ if (ret)
+ return ret;
+
+ key = "qcom,local-pid";
+ ret = of_property_read_u32(pdev->dev.of_node, key, &smp2p->local_pid);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to read %s\n", key);
+ return -EINVAL;
+ }
+
+ key = "qcom,remote-pid";
+ ret = of_property_read_u32(pdev->dev.of_node, key, &smp2p->remote_pid);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to read %s\n", key);
+ return -EINVAL;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "unable to acquire smp2p interrupt\n");
+ return irq;
+ }
+
+ ret = qcom_smp2p_alloc_outbound_item(smp2p);
+ if (ret < 0)
+ return ret;
+
+ for_each_available_child_of_node(pdev->dev.of_node, node) {
+ entry = devm_kzalloc(&pdev->dev, sizeof(*entry), GFP_KERNEL);
+ if (!entry) {
+ ret = -ENOMEM;
+ goto unwind_interfaces;
+ }
+
+ entry->smp2p = smp2p;
+ spin_lock_init(&entry->lock);
+
+ ret = of_property_read_string(node, "qcom,entry-name", &entry->name);
+ if (ret < 0)
+ goto unwind_interfaces;
+
+ if (of_property_read_bool(node, "interrupt-controller")) {
+ ret = qcom_smp2p_inbound_entry(smp2p, entry, node);
+ if (ret < 0)
+ goto unwind_interfaces;
+
+ list_add(&entry->node, &smp2p->inbound);
+ } else {
+ ret = qcom_smp2p_outbound_entry(smp2p, entry, node);
+ if (ret < 0)
+ goto unwind_interfaces;
+
+ list_add(&entry->node, &smp2p->outbound);
+ }
+ }
+
+ /* Kick the outgoing edge after allocating entries */
+ qcom_smp2p_kick(smp2p);
+
+ ret = devm_request_threaded_irq(&pdev->dev, irq,
+ NULL, qcom_smp2p_intr,
+ IRQF_ONESHOT,
+ "smp2p", (void *)smp2p);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to request interrupt\n");
+ goto unwind_interfaces;
+ }
+
+
+ return 0;
+
+unwind_interfaces:
+ list_for_each_entry(entry, &smp2p->inbound, node)
+ irq_domain_remove(entry->domain);
+
+ list_for_each_entry(entry, &smp2p->outbound, node)
+ qcom_smem_state_unregister(entry->state);
+
+ smp2p->out->valid_entries = 0;
+
+ return ret;
+}
+
+static int qcom_smp2p_remove(struct platform_device *pdev)
+{
+ struct qcom_smp2p *smp2p = platform_get_drvdata(pdev);
+ struct smp2p_entry *entry;
+
+ list_for_each_entry(entry, &smp2p->inbound, node)
+ irq_domain_remove(entry->domain);
+
+ list_for_each_entry(entry, &smp2p->outbound, node)
+ qcom_smem_state_unregister(entry->state);
+
+ smp2p->out->valid_entries = 0;
+
+ return 0;
+}
+
+static const struct of_device_id qcom_smp2p_of_match[] = {
+ { .compatible = "qcom,smp2p" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, qcom_smp2p_of_match);
+
+static struct platform_driver qcom_smp2p_driver = {
+ .probe = qcom_smp2p_probe,
+ .remove = qcom_smp2p_remove,
+ .driver = {
+ .name = "qcom_smp2p",
+ .of_match_table = qcom_smp2p_of_match,
+ },
+};
+module_platform_driver(qcom_smp2p_driver);
+
+MODULE_DESCRIPTION("Qualcomm Shared Memory Point to Point driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/soc/qcom/smsm.c b/drivers/soc/qcom/smsm.c
new file mode 100644
index 0000000..6b777af
--- /dev/null
+++ b/drivers/soc/qcom/smsm.c
@@ -0,0 +1,625 @@
+/*
+ * Copyright (c) 2015, Sony Mobile Communications Inc.
+ * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include <linux/regmap.h>
+#include <linux/soc/qcom/smem.h>
+#include <linux/soc/qcom/smem_state.h>
+
+/*
+ * This driver implements the Qualcomm Shared Memory State Machine, a mechanism
+ * for communicating single bit state information to remote processors.
+ *
+ * The implementation is based on two sections of shared memory; the first
+ * holding the state bits and the second holding a matrix of subscription bits.
+ *
+ * The state bits are structured in entries of 32 bits, each belonging to one
+ * system in the SoC. The entry belonging to the local system is considered
+ * read-write, while the rest should be considered read-only.
+ *
+ * The subscription matrix consists of N bitmaps per entry, denoting interest
+ * in updates of the entry for each of the N hosts. Upon updating a state bit
+ * each host's subscription bitmap should be queried and the remote system
+ * should be interrupted if they request so.
+ *
+ * The subscription matrix is laid out in entry-major order:
+ * entry0: [host0 ... hostN]
+ * .
+ * .
+ * entryM: [host0 ... hostN]
+ *
+ * A third, optional, shared memory region might contain information regarding
+ * the number of entries in the state bitmap as well as number of columns in
+ * the subscription matrix.
+ */
+
+/*
+ * Shared memory identifiers, used to acquire handles to respective memory
+ * region.
+ */
+#define SMEM_SMSM_SHARED_STATE 85
+#define SMEM_SMSM_CPU_INTR_MASK 333
+#define SMEM_SMSM_SIZE_INFO 419
+
+/*
+ * Default sizes, in case SMEM_SMSM_SIZE_INFO is not found.
+ */
+#define SMSM_DEFAULT_NUM_ENTRIES 8
+#define SMSM_DEFAULT_NUM_HOSTS 3
+
+struct smsm_entry;
+struct smsm_host;
+
+/**
+ * struct qcom_smsm - smsm driver context
+ * @dev: smsm device pointer
+ * @local_host: column in the subscription matrix representing this system
+ * @num_hosts: number of columns in the subscription matrix
+ * @num_entries: number of entries in the state map and rows in the subscription
+ * matrix
+ * @local_state: pointer to the local processor's state bits
+ * @subscription: pointer to local processor's row in subscription matrix
+ * @state: smem state handle
+ * @lock: spinlock for read-modify-write of the outgoing state
+ * @entries: context for each of the entries
+ * @hosts: context for each of the hosts
+ */
+struct qcom_smsm {
+ struct device *dev;
+
+ u32 local_host;
+
+ u32 num_hosts;
+ u32 num_entries;
+
+ u32 *local_state;
+ u32 *subscription;
+ struct qcom_smem_state *state;
+
+ spinlock_t lock;
+
+ struct smsm_entry *entries;
+ struct smsm_host *hosts;
+};
+
+/**
+ * struct smsm_entry - per remote processor entry context
+ * @smsm: back-reference to driver context
+ * @domain: IRQ domain for this entry, if representing a remote system
+ * @irq_enabled: bitmap of which state bits IRQs are enabled
+ * @irq_rising: bitmap tracking if rising bits should be propagated
+ * @irq_falling: bitmap tracking if falling bits should be propagated
+ * @last_value: snapshot of state bits last time the interrupts where propagated
+ * @remote_state: pointer to this entry's state bits
+ * @subscription: pointer to a row in the subscription matrix representing this
+ * entry
+ */
+struct smsm_entry {
+ struct qcom_smsm *smsm;
+
+ struct irq_domain *domain;
+ DECLARE_BITMAP(irq_enabled, 32);
+ DECLARE_BITMAP(irq_rising, 32);
+ DECLARE_BITMAP(irq_falling, 32);
+ u32 last_value;
+
+ u32 *remote_state;
+ u32 *subscription;
+};
+
+/**
+ * struct smsm_host - representation of a remote host
+ * @ipc_regmap: regmap for outgoing interrupt
+ * @ipc_offset: offset in @ipc_regmap for outgoing interrupt
+ * @ipc_bit: bit in @ipc_regmap + @ipc_offset for outgoing interrupt
+ */
+struct smsm_host {
+ struct regmap *ipc_regmap;
+ int ipc_offset;
+ int ipc_bit;
+};
+
+/**
+ * smsm_update_bits() - change bit in outgoing entry and inform subscribers
+ * @data: smsm context pointer
+ * @offset: bit in the entry
+ * @value: new value
+ *
+ * Used to set and clear the bits in the outgoing/local entry and inform
+ * subscribers about the change.
+ */
+static int smsm_update_bits(void *data, u32 mask, u32 value)
+{
+ struct qcom_smsm *smsm = data;
+ struct smsm_host *hostp;
+ unsigned long flags;
+ u32 changes;
+ u32 host;
+ u32 orig;
+ u32 val;
+
+ spin_lock_irqsave(&smsm->lock, flags);
+
+ /* Update the entry */
+ val = orig = readl(smsm->local_state);
+ val &= ~mask;
+ val |= value;
+
+ /* Don't signal if we didn't change the value */
+ changes = val ^ orig;
+ if (!changes) {
+ spin_unlock_irqrestore(&smsm->lock, flags);
+ goto done;
+ }
+
+ /* Write out the new value */
+ writel(val, smsm->local_state);
+ spin_unlock_irqrestore(&smsm->lock, flags);
+
+ /* Make sure the value update is ordered before any kicks */
+ wmb();
+
+ /* Iterate over all hosts to check whom wants a kick */
+ for (host = 0; host < smsm->num_hosts; host++) {
+ hostp = &smsm->hosts[host];
+
+ val = readl(smsm->subscription + host);
+ if (val & changes && hostp->ipc_regmap) {
+ regmap_write(hostp->ipc_regmap,
+ hostp->ipc_offset,
+ BIT(hostp->ipc_bit));
+ }
+ }
+
+done:
+ return 0;
+}
+
+static const struct qcom_smem_state_ops smsm_state_ops = {
+ .update_bits = smsm_update_bits,
+};
+
+/**
+ * smsm_intr() - cascading IRQ handler for SMSM
+ * @irq: unused
+ * @data: entry related to this IRQ
+ *
+ * This function cascades an incoming interrupt from a remote system, based on
+ * the state bits and configuration.
+ */
+static irqreturn_t smsm_intr(int irq, void *data)
+{
+ struct smsm_entry *entry = data;
+ unsigned i;
+ int irq_pin;
+ u32 changed;
+ u32 val;
+
+ val = readl(entry->remote_state);
+ changed = val ^ entry->last_value;
+ entry->last_value = val;
+
+ for_each_set_bit(i, entry->irq_enabled, 32) {
+ if (!(changed & BIT(i)))
+ continue;
+
+ if (val & BIT(i)) {
+ if (test_bit(i, entry->irq_rising)) {
+ irq_pin = irq_find_mapping(entry->domain, i);
+ handle_nested_irq(irq_pin);
+ }
+ } else {
+ if (test_bit(i, entry->irq_falling)) {
+ irq_pin = irq_find_mapping(entry->domain, i);
+ handle_nested_irq(irq_pin);
+ }
+ }
+ }
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * smsm_mask_irq() - un-subscribe from cascades of IRQs of a certain staus bit
+ * @irqd: IRQ handle to be masked
+ *
+ * This un-subscribes the local CPU from interrupts upon changes to the defines
+ * status bit. The bit is also cleared from cascading.
+ */
+static void smsm_mask_irq(struct irq_data *irqd)
+{
+ struct smsm_entry *entry = irq_data_get_irq_chip_data(irqd);
+ irq_hw_number_t irq = irqd_to_hwirq(irqd);
+ struct qcom_smsm *smsm = entry->smsm;
+ u32 val;
+
+ if (entry->subscription) {
+ val = readl(entry->subscription + smsm->local_host);
+ val &= ~BIT(irq);
+ writel(val, entry->subscription + smsm->local_host);
+ }
+
+ clear_bit(irq, entry->irq_enabled);
+}
+
+/**
+ * smsm_unmask_irq() - subscribe to cascades of IRQs of a certain status bit
+ * @irqd: IRQ handle to be unmasked
+ *
+
+ * This subscribes the local CPU to interrupts upon changes to the defined
+ * status bit. The bit is also marked for cascading.
+
+ */
+static void smsm_unmask_irq(struct irq_data *irqd)
+{
+ struct smsm_entry *entry = irq_data_get_irq_chip_data(irqd);
+ irq_hw_number_t irq = irqd_to_hwirq(irqd);
+ struct qcom_smsm *smsm = entry->smsm;
+ u32 val;
+
+ set_bit(irq, entry->irq_enabled);
+
+ if (entry->subscription) {
+ val = readl(entry->subscription + smsm->local_host);
+ val |= BIT(irq);
+ writel(val, entry->subscription + smsm->local_host);
+ }
+}
+
+/**
+ * smsm_set_irq_type() - updates the requested IRQ type for the cascading
+ * @irqd: consumer interrupt handle
+ * @type: requested flags
+ */
+static int smsm_set_irq_type(struct irq_data *irqd, unsigned int type)
+{
+ struct smsm_entry *entry = irq_data_get_irq_chip_data(irqd);
+ irq_hw_number_t irq = irqd_to_hwirq(irqd);
+
+ if (!(type & IRQ_TYPE_EDGE_BOTH))
+ return -EINVAL;
+
+ if (type & IRQ_TYPE_EDGE_RISING)
+ set_bit(irq, entry->irq_rising);
+ else
+ clear_bit(irq, entry->irq_rising);
+
+ if (type & IRQ_TYPE_EDGE_FALLING)
+ set_bit(irq, entry->irq_falling);
+ else
+ clear_bit(irq, entry->irq_falling);
+
+ return 0;
+}
+
+static struct irq_chip smsm_irq_chip = {
+ .name = "smsm",
+ .irq_mask = smsm_mask_irq,
+ .irq_unmask = smsm_unmask_irq,
+ .irq_set_type = smsm_set_irq_type,
+};
+
+/**
+ * smsm_irq_map() - sets up a mapping for a cascaded IRQ
+ * @d: IRQ domain representing an entry
+ * @irq: IRQ to set up
+ * @hw: unused
+ */
+static int smsm_irq_map(struct irq_domain *d,
+ unsigned int irq,
+ irq_hw_number_t hw)
+{
+ struct smsm_entry *entry = d->host_data;
+
+ irq_set_chip_and_handler(irq, &smsm_irq_chip, handle_level_irq);
+ irq_set_chip_data(irq, entry);
+ irq_set_nested_thread(irq, 1);
+
+ return 0;
+}
+
+static const struct irq_domain_ops smsm_irq_ops = {
+ .map = smsm_irq_map,
+ .xlate = irq_domain_xlate_twocell,
+};
+
+/**
+ * smsm_parse_ipc() - parses a qcom,ipc-%d device tree property
+ * @smsm: smsm driver context
+ * @host_id: index of the remote host to be resolved
+ *
+ * Parses device tree to acquire the information needed for sending the
+ * outgoing interrupts to a remote host - identified by @host_id.
+ */
+static int smsm_parse_ipc(struct qcom_smsm *smsm, unsigned host_id)
+{
+ struct device_node *syscon;
+ struct device_node *node = smsm->dev->of_node;
+ struct smsm_host *host = &smsm->hosts[host_id];
+ char key[16];
+ int ret;
+
+ snprintf(key, sizeof(key), "qcom,ipc-%d", host_id);
+ syscon = of_parse_phandle(node, key, 0);
+ if (!syscon)
+ return 0;
+
+ host->ipc_regmap = syscon_node_to_regmap(syscon);
+ if (IS_ERR(host->ipc_regmap))
+ return PTR_ERR(host->ipc_regmap);
+
+ ret = of_property_read_u32_index(node, key, 1, &host->ipc_offset);
+ if (ret < 0) {
+ dev_err(smsm->dev, "no offset in %s\n", key);
+ return -EINVAL;
+ }
+
+ ret = of_property_read_u32_index(node, key, 2, &host->ipc_bit);
+ if (ret < 0) {
+ dev_err(smsm->dev, "no bit in %s\n", key);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * smsm_inbound_entry() - parse DT and set up an entry representing a remote system
+ * @smsm: smsm driver context
+ * @entry: entry context to be set up
+ * @node: dt node containing the entry's properties
+ */
+static int smsm_inbound_entry(struct qcom_smsm *smsm,
+ struct smsm_entry *entry,
+ struct device_node *node)
+{
+ int ret;
+ int irq;
+
+ irq = irq_of_parse_and_map(node, 0);
+ if (!irq) {
+ dev_err(smsm->dev, "failed to parse smsm interrupt\n");
+ return -EINVAL;
+ }
+
+ ret = devm_request_threaded_irq(smsm->dev, irq,
+ NULL, smsm_intr,
+ IRQF_ONESHOT,
+ "smsm", (void *)entry);
+ if (ret) {
+ dev_err(smsm->dev, "failed to request interrupt\n");
+ return ret;
+ }
+
+ entry->domain = irq_domain_add_linear(node, 32, &smsm_irq_ops, entry);
+ if (!entry->domain) {
+ dev_err(smsm->dev, "failed to add irq_domain\n");
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+/**
+ * smsm_get_size_info() - parse the optional memory segment for sizes
+ * @smsm: smsm driver context
+ *
+ * Attempt to acquire the number of hosts and entries from the optional shared
+ * memory location. Not being able to find this segment should indicate that
+ * we're on a older system where these values was hard coded to
+ * SMSM_DEFAULT_NUM_ENTRIES and SMSM_DEFAULT_NUM_HOSTS.
+ *
+ * Returns 0 on success, negative errno on failure.
+ */
+static int smsm_get_size_info(struct qcom_smsm *smsm)
+{
+ size_t size;
+ struct {
+ u32 num_hosts;
+ u32 num_entries;
+ u32 reserved0;
+ u32 reserved1;
+ } *info;
+
+ info = qcom_smem_get(QCOM_SMEM_HOST_ANY, SMEM_SMSM_SIZE_INFO, &size);
+ if (PTR_ERR(info) == -ENOENT || size != sizeof(*info)) {
+ dev_warn(smsm->dev, "no smsm size info, using defaults\n");
+ smsm->num_entries = SMSM_DEFAULT_NUM_ENTRIES;
+ smsm->num_hosts = SMSM_DEFAULT_NUM_HOSTS;
+ return 0;
+ } else if (IS_ERR(info)) {
+ dev_err(smsm->dev, "unable to retrieve smsm size info\n");
+ return PTR_ERR(info);
+ }
+
+ smsm->num_entries = info->num_entries;
+ smsm->num_hosts = info->num_hosts;
+
+ dev_dbg(smsm->dev,
+ "found custom size of smsm: %d entries %d hosts\n",
+ smsm->num_entries, smsm->num_hosts);
+
+ return 0;
+}
+
+static int qcom_smsm_probe(struct platform_device *pdev)
+{
+ struct device_node *local_node;
+ struct device_node *node;
+ struct smsm_entry *entry;
+ struct qcom_smsm *smsm;
+ u32 *intr_mask;
+ size_t size;
+ u32 *states;
+ u32 id;
+ int ret;
+
+ smsm = devm_kzalloc(&pdev->dev, sizeof(*smsm), GFP_KERNEL);
+ if (!smsm)
+ return -ENOMEM;
+ smsm->dev = &pdev->dev;
+ spin_lock_init(&smsm->lock);
+
+ ret = smsm_get_size_info(smsm);
+ if (ret)
+ return ret;
+
+ smsm->entries = devm_kcalloc(&pdev->dev,
+ smsm->num_entries,
+ sizeof(struct smsm_entry),
+ GFP_KERNEL);
+ if (!smsm->entries)
+ return -ENOMEM;
+
+ smsm->hosts = devm_kcalloc(&pdev->dev,
+ smsm->num_hosts,
+ sizeof(struct smsm_host),
+ GFP_KERNEL);
+ if (!smsm->hosts)
+ return -ENOMEM;
+
+ local_node = of_find_node_with_property(pdev->dev.of_node, "#qcom,state-cells");
+ if (!local_node) {
+ dev_err(&pdev->dev, "no state entry\n");
+ return -EINVAL;
+ }
+
+ of_property_read_u32(pdev->dev.of_node,
+ "qcom,local-host",
+ &smsm->local_host);
+
+ /* Parse the host properties */
+ for (id = 0; id < smsm->num_hosts; id++) {
+ ret = smsm_parse_ipc(smsm, id);
+ if (ret < 0)
+ return ret;
+ }
+
+ /* Acquire the main SMSM state vector */
+ ret = qcom_smem_alloc(QCOM_SMEM_HOST_ANY, SMEM_SMSM_SHARED_STATE,
+ smsm->num_entries * sizeof(u32));
+ if (ret < 0 && ret != -EEXIST) {
+ dev_err(&pdev->dev, "unable to allocate shared state entry\n");
+ return ret;
+ }
+
+ states = qcom_smem_get(QCOM_SMEM_HOST_ANY, SMEM_SMSM_SHARED_STATE, NULL);
+ if (IS_ERR(states)) {
+ dev_err(&pdev->dev, "Unable to acquire shared state entry\n");
+ return PTR_ERR(states);
+ }
+
+ /* Acquire the list of interrupt mask vectors */
+ size = smsm->num_entries * smsm->num_hosts * sizeof(u32);
+ ret = qcom_smem_alloc(QCOM_SMEM_HOST_ANY, SMEM_SMSM_CPU_INTR_MASK, size);
+ if (ret < 0 && ret != -EEXIST) {
+ dev_err(&pdev->dev, "unable to allocate smsm interrupt mask\n");
+ return ret;
+ }
+
+ intr_mask = qcom_smem_get(QCOM_SMEM_HOST_ANY, SMEM_SMSM_CPU_INTR_MASK, NULL);
+ if (IS_ERR(intr_mask)) {
+ dev_err(&pdev->dev, "unable to acquire shared memory interrupt mask\n");
+ return PTR_ERR(intr_mask);
+ }
+
+ /* Setup the reference to the local state bits */
+ smsm->local_state = states + smsm->local_host;
+ smsm->subscription = intr_mask + smsm->local_host * smsm->num_hosts;
+
+ /* Register the outgoing state */
+ smsm->state = qcom_smem_state_register(local_node, &smsm_state_ops, smsm);
+ if (IS_ERR(smsm->state)) {
+ dev_err(smsm->dev, "failed to register qcom_smem_state\n");
+ return PTR_ERR(smsm->state);
+ }
+
+ /* Register handlers for remote processor entries of interest. */
+ for_each_available_child_of_node(pdev->dev.of_node, node) {
+ if (!of_property_read_bool(node, "interrupt-controller"))
+ continue;
+
+ ret = of_property_read_u32(node, "reg", &id);
+ if (ret || id >= smsm->num_entries) {
+ dev_err(&pdev->dev, "invalid reg of entry\n");
+ if (!ret)
+ ret = -EINVAL;
+ goto unwind_interfaces;
+ }
+ entry = &smsm->entries[id];
+
+ entry->smsm = smsm;
+ entry->remote_state = states + id;
+
+ /* Setup subscription pointers and unsubscribe to any kicks */
+ entry->subscription = intr_mask + id * smsm->num_hosts;
+ writel(0, entry->subscription + smsm->local_host);
+
+ ret = smsm_inbound_entry(smsm, entry, node);
+ if (ret < 0)
+ goto unwind_interfaces;
+ }
+
+ platform_set_drvdata(pdev, smsm);
+
+ return 0;
+
+unwind_interfaces:
+ for (id = 0; id < smsm->num_entries; id++)
+ if (smsm->entries[id].domain)
+ irq_domain_remove(smsm->entries[id].domain);
+
+ qcom_smem_state_unregister(smsm->state);
+
+ return ret;
+}
+
+static int qcom_smsm_remove(struct platform_device *pdev)
+{
+ struct qcom_smsm *smsm = platform_get_drvdata(pdev);
+ unsigned id;
+
+ for (id = 0; id < smsm->num_entries; id++)
+ if (smsm->entries[id].domain)
+ irq_domain_remove(smsm->entries[id].domain);
+
+ qcom_smem_state_unregister(smsm->state);
+
+ return 0;
+}
+
+static const struct of_device_id qcom_smsm_of_match[] = {
+ { .compatible = "qcom,smsm" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, qcom_smsm_of_match);
+
+static struct platform_driver qcom_smsm_driver = {
+ .probe = qcom_smsm_probe,
+ .remove = qcom_smsm_remove,
+ .driver = {
+ .name = "qcom-smsm",
+ .of_match_table = qcom_smsm_of_match,
+ },
+};
+module_platform_driver(qcom_smsm_driver);
+
+MODULE_DESCRIPTION("Qualcomm Shared Memory State Machine driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/soc/qcom/wcnss_ctrl.c b/drivers/soc/qcom/wcnss_ctrl.c
new file mode 100644
index 0000000..7a986f8
--- /dev/null
+++ b/drivers/soc/qcom/wcnss_ctrl.c
@@ -0,0 +1,272 @@
+/*
+ * Copyright (c) 2015, Sony Mobile Communications Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/firmware.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/soc/qcom/smd.h>
+
+#define WCNSS_REQUEST_TIMEOUT (5 * HZ)
+
+#define NV_FRAGMENT_SIZE 3072
+#define NVBIN_FILE "wlan/prima/WCNSS_qcom_wlan_nv.bin"
+
+/**
+ * struct wcnss_ctrl - driver context
+ * @dev: device handle
+ * @channel: SMD channel handle
+ * @ack: completion for outstanding requests
+ * @ack_status: status of the outstanding request
+ * @download_nv_work: worker for uploading nv binary
+ */
+struct wcnss_ctrl {
+ struct device *dev;
+ struct qcom_smd_channel *channel;
+
+ struct completion ack;
+ int ack_status;
+
+ struct work_struct download_nv_work;
+};
+
+/* message types */
+enum {
+ WCNSS_VERSION_REQ = 0x01000000,
+ WCNSS_VERSION_RESP,
+ WCNSS_DOWNLOAD_NV_REQ,
+ WCNSS_DOWNLOAD_NV_RESP,
+ WCNSS_UPLOAD_CAL_REQ,
+ WCNSS_UPLOAD_CAL_RESP,
+ WCNSS_DOWNLOAD_CAL_REQ,
+ WCNSS_DOWNLOAD_CAL_RESP,
+};
+
+/**
+ * struct wcnss_msg_hdr - common packet header for requests and responses
+ * @type: packet message type
+ * @len: total length of the packet, including this header
+ */
+struct wcnss_msg_hdr {
+ u32 type;
+ u32 len;
+} __packed;
+
+/**
+ * struct wcnss_version_resp - version request response
+ * @hdr: common packet wcnss_msg_hdr header
+ */
+struct wcnss_version_resp {
+ struct wcnss_msg_hdr hdr;
+ u8 major;
+ u8 minor;
+ u8 version;
+ u8 revision;
+} __packed;
+
+/**
+ * struct wcnss_download_nv_req - firmware fragment request
+ * @hdr: common packet wcnss_msg_hdr header
+ * @seq: sequence number of this fragment
+ * @last: boolean indicator of this being the last fragment of the binary
+ * @frag_size: length of this fragment
+ * @fragment: fragment data
+ */
+struct wcnss_download_nv_req {
+ struct wcnss_msg_hdr hdr;
+ u16 seq;
+ u16 last;
+ u32 frag_size;
+ u8 fragment[];
+} __packed;
+
+/**
+ * struct wcnss_download_nv_resp - firmware download response
+ * @hdr: common packet wcnss_msg_hdr header
+ * @status: boolean to indicate success of the download
+ */
+struct wcnss_download_nv_resp {
+ struct wcnss_msg_hdr hdr;
+ u8 status;
+} __packed;
+
+/**
+ * wcnss_ctrl_smd_callback() - handler from SMD responses
+ * @qsdev: smd device handle
+ * @data: pointer to the incoming data packet
+ * @count: size of the incoming data packet
+ *
+ * Handles any incoming packets from the remote WCNSS_CTRL service.
+ */
+static int wcnss_ctrl_smd_callback(struct qcom_smd_device *qsdev,
+ const void *data,
+ size_t count)
+{
+ struct wcnss_ctrl *wcnss = dev_get_drvdata(&qsdev->dev);
+ const struct wcnss_download_nv_resp *nvresp;
+ const struct wcnss_version_resp *version;
+ const struct wcnss_msg_hdr *hdr = data;
+
+ switch (hdr->type) {
+ case WCNSS_VERSION_RESP:
+ if (count != sizeof(*version)) {
+ dev_err(wcnss->dev,
+ "invalid size of version response\n");
+ break;
+ }
+
+ version = data;
+ dev_info(wcnss->dev, "WCNSS Version %d.%d %d.%d\n",
+ version->major, version->minor,
+ version->version, version->revision);
+
+ schedule_work(&wcnss->download_nv_work);
+ break;
+ case WCNSS_DOWNLOAD_NV_RESP:
+ if (count != sizeof(*nvresp)) {
+ dev_err(wcnss->dev,
+ "invalid size of download response\n");
+ break;
+ }
+
+ nvresp = data;
+ wcnss->ack_status = nvresp->status;
+ complete(&wcnss->ack);
+ break;
+ default:
+ dev_info(wcnss->dev, "unknown message type %d\n", hdr->type);
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * wcnss_request_version() - send a version request to WCNSS
+ * @wcnss: wcnss ctrl driver context
+ */
+static int wcnss_request_version(struct wcnss_ctrl *wcnss)
+{
+ struct wcnss_msg_hdr msg;
+
+ msg.type = WCNSS_VERSION_REQ;
+ msg.len = sizeof(msg);
+
+ return qcom_smd_send(wcnss->channel, &msg, sizeof(msg));
+}
+
+/**
+ * wcnss_download_nv() - send nv binary to WCNSS
+ * @work: work struct to acquire wcnss context
+ */
+static void wcnss_download_nv(struct work_struct *work)
+{
+ struct wcnss_ctrl *wcnss = container_of(work, struct wcnss_ctrl, download_nv_work);
+ struct wcnss_download_nv_req *req;
+ const struct firmware *fw;
+ const void *data;
+ ssize_t left;
+ int ret;
+
+ req = kzalloc(sizeof(*req) + NV_FRAGMENT_SIZE, GFP_KERNEL);
+ if (!req)
+ return;
+
+ ret = request_firmware(&fw, NVBIN_FILE, wcnss->dev);
+ if (ret) {
+ dev_err(wcnss->dev, "Failed to load nv file %s: %d\n",
+ NVBIN_FILE, ret);
+ goto free_req;
+ }
+
+ data = fw->data;
+ left = fw->size;
+
+ req->hdr.type = WCNSS_DOWNLOAD_NV_REQ;
+ req->hdr.len = sizeof(*req) + NV_FRAGMENT_SIZE;
+
+ req->last = 0;
+ req->frag_size = NV_FRAGMENT_SIZE;
+
+ req->seq = 0;
+ do {
+ if (left <= NV_FRAGMENT_SIZE) {
+ req->last = 1;
+ req->frag_size = left;
+ req->hdr.len = sizeof(*req) + left;
+ }
+
+ memcpy(req->fragment, data, req->frag_size);
+
+ ret = qcom_smd_send(wcnss->channel, req, req->hdr.len);
+ if (ret) {
+ dev_err(wcnss->dev, "failed to send smd packet\n");
+ goto release_fw;
+ }
+
+ /* Increment for next fragment */
+ req->seq++;
+
+ data += req->hdr.len;
+ left -= NV_FRAGMENT_SIZE;
+ } while (left > 0);
+
+ ret = wait_for_completion_timeout(&wcnss->ack, WCNSS_REQUEST_TIMEOUT);
+ if (!ret)
+ dev_err(wcnss->dev, "timeout waiting for nv upload ack\n");
+ else if (wcnss->ack_status != 1)
+ dev_err(wcnss->dev, "nv upload response failed err: %d\n",
+ wcnss->ack_status);
+
+release_fw:
+ release_firmware(fw);
+free_req:
+ kfree(req);
+}
+
+static int wcnss_ctrl_probe(struct qcom_smd_device *sdev)
+{
+ struct wcnss_ctrl *wcnss;
+
+ wcnss = devm_kzalloc(&sdev->dev, sizeof(*wcnss), GFP_KERNEL);
+ if (!wcnss)
+ return -ENOMEM;
+
+ wcnss->dev = &sdev->dev;
+ wcnss->channel = sdev->channel;
+
+ init_completion(&wcnss->ack);
+ INIT_WORK(&wcnss->download_nv_work, wcnss_download_nv);
+
+ dev_set_drvdata(&sdev->dev, wcnss);
+
+ return wcnss_request_version(wcnss);
+}
+
+static const struct qcom_smd_id wcnss_ctrl_smd_match[] = {
+ { .name = "WCNSS_CTRL" },
+ {}
+};
+
+static struct qcom_smd_driver wcnss_ctrl_driver = {
+ .probe = wcnss_ctrl_probe,
+ .callback = wcnss_ctrl_smd_callback,
+ .smd_match_table = wcnss_ctrl_smd_match,
+ .driver = {
+ .name = "qcom_wcnss_ctrl",
+ .owner = THIS_MODULE,
+ },
+};
+
+module_qcom_smd_driver(wcnss_ctrl_driver);
+
+MODULE_DESCRIPTION("Qualcomm WCNSS control driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/soc/ti/Kconfig b/drivers/soc/ti/Kconfig
index 7266b21..3557c5e 100644
--- a/drivers/soc/ti/Kconfig
+++ b/drivers/soc/ti/Kconfig
@@ -28,4 +28,14 @@
If unsure, say N.
+config WKUP_M3_IPC
+ tristate "TI AMx3 Wkup-M3 IPC Driver"
+ depends on WKUP_M3_RPROC
+ depends on OMAP2PLUS_MBOX
+ help
+ TI AM33XX and AM43XX have a Cortex M3, the Wakeup M3, to handle
+ low power transitions. This IPC driver provides the necessary API
+ to communicate and use the Wakeup M3 for PM features like suspend
+ resume and boots it using wkup_m3_rproc driver.
+
endif # SOC_TI
diff --git a/drivers/soc/ti/Makefile b/drivers/soc/ti/Makefile
index 135bdad..48ff3a7 100644
--- a/drivers/soc/ti/Makefile
+++ b/drivers/soc/ti/Makefile
@@ -4,3 +4,4 @@
obj-$(CONFIG_KEYSTONE_NAVIGATOR_QMSS) += knav_qmss.o
knav_qmss-y := knav_qmss_queue.o knav_qmss_acc.o
obj-$(CONFIG_KEYSTONE_NAVIGATOR_DMA) += knav_dma.o
+obj-$(CONFIG_WKUP_M3_IPC) += wkup_m3_ipc.o
diff --git a/drivers/soc/ti/wkup_m3_ipc.c b/drivers/soc/ti/wkup_m3_ipc.c
new file mode 100644
index 0000000..8823cc8
--- /dev/null
+++ b/drivers/soc/ti/wkup_m3_ipc.c
@@ -0,0 +1,508 @@
+/*
+ * AMx3 Wkup M3 IPC driver
+ *
+ * Copyright (C) 2015 Texas Instruments, Inc.
+ *
+ * Dave Gerlach <d-gerlach@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/kthread.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/omap-mailbox.h>
+#include <linux/platform_device.h>
+#include <linux/remoteproc.h>
+#include <linux/suspend.h>
+#include <linux/wkup_m3_ipc.h>
+
+#define AM33XX_CTRL_IPC_REG_COUNT 0x8
+#define AM33XX_CTRL_IPC_REG_OFFSET(m) (0x4 + 4 * (m))
+
+/* AM33XX M3_TXEV_EOI register */
+#define AM33XX_CONTROL_M3_TXEV_EOI 0x00
+
+#define AM33XX_M3_TXEV_ACK (0x1 << 0)
+#define AM33XX_M3_TXEV_ENABLE (0x0 << 0)
+
+#define IPC_CMD_DS0 0x4
+#define IPC_CMD_STANDBY 0xc
+#define IPC_CMD_IDLE 0x10
+#define IPC_CMD_RESET 0xe
+#define DS_IPC_DEFAULT 0xffffffff
+#define M3_VERSION_UNKNOWN 0x0000ffff
+#define M3_BASELINE_VERSION 0x191
+#define M3_STATUS_RESP_MASK (0xffff << 16)
+#define M3_FW_VERSION_MASK 0xffff
+
+#define M3_STATE_UNKNOWN 0
+#define M3_STATE_RESET 1
+#define M3_STATE_INITED 2
+#define M3_STATE_MSG_FOR_LP 3
+#define M3_STATE_MSG_FOR_RESET 4
+
+static struct wkup_m3_ipc *m3_ipc_state;
+
+static void am33xx_txev_eoi(struct wkup_m3_ipc *m3_ipc)
+{
+ writel(AM33XX_M3_TXEV_ACK,
+ m3_ipc->ipc_mem_base + AM33XX_CONTROL_M3_TXEV_EOI);
+}
+
+static void am33xx_txev_enable(struct wkup_m3_ipc *m3_ipc)
+{
+ writel(AM33XX_M3_TXEV_ENABLE,
+ m3_ipc->ipc_mem_base + AM33XX_CONTROL_M3_TXEV_EOI);
+}
+
+static void wkup_m3_ctrl_ipc_write(struct wkup_m3_ipc *m3_ipc,
+ u32 val, int ipc_reg_num)
+{
+ if (WARN(ipc_reg_num < 0 || ipc_reg_num > AM33XX_CTRL_IPC_REG_COUNT,
+ "ipc register operation out of range"))
+ return;
+
+ writel(val, m3_ipc->ipc_mem_base +
+ AM33XX_CTRL_IPC_REG_OFFSET(ipc_reg_num));
+}
+
+static unsigned int wkup_m3_ctrl_ipc_read(struct wkup_m3_ipc *m3_ipc,
+ int ipc_reg_num)
+{
+ if (WARN(ipc_reg_num < 0 || ipc_reg_num > AM33XX_CTRL_IPC_REG_COUNT,
+ "ipc register operation out of range"))
+ return 0;
+
+ return readl(m3_ipc->ipc_mem_base +
+ AM33XX_CTRL_IPC_REG_OFFSET(ipc_reg_num));
+}
+
+static int wkup_m3_fw_version_read(struct wkup_m3_ipc *m3_ipc)
+{
+ int val;
+
+ val = wkup_m3_ctrl_ipc_read(m3_ipc, 2);
+
+ return val & M3_FW_VERSION_MASK;
+}
+
+static irqreturn_t wkup_m3_txev_handler(int irq, void *ipc_data)
+{
+ struct wkup_m3_ipc *m3_ipc = ipc_data;
+ struct device *dev = m3_ipc->dev;
+ int ver = 0;
+
+ am33xx_txev_eoi(m3_ipc);
+
+ switch (m3_ipc->state) {
+ case M3_STATE_RESET:
+ ver = wkup_m3_fw_version_read(m3_ipc);
+
+ if (ver == M3_VERSION_UNKNOWN ||
+ ver < M3_BASELINE_VERSION) {
+ dev_warn(dev, "CM3 Firmware Version %x not supported\n",
+ ver);
+ } else {
+ dev_info(dev, "CM3 Firmware Version = 0x%x\n", ver);
+ }
+
+ m3_ipc->state = M3_STATE_INITED;
+ complete(&m3_ipc->sync_complete);
+ break;
+ case M3_STATE_MSG_FOR_RESET:
+ m3_ipc->state = M3_STATE_INITED;
+ complete(&m3_ipc->sync_complete);
+ break;
+ case M3_STATE_MSG_FOR_LP:
+ complete(&m3_ipc->sync_complete);
+ break;
+ case M3_STATE_UNKNOWN:
+ dev_warn(dev, "Unknown CM3 State\n");
+ }
+
+ am33xx_txev_enable(m3_ipc);
+
+ return IRQ_HANDLED;
+}
+
+static int wkup_m3_ping(struct wkup_m3_ipc *m3_ipc)
+{
+ struct device *dev = m3_ipc->dev;
+ mbox_msg_t dummy_msg = 0;
+ int ret;
+
+ if (!m3_ipc->mbox) {
+ dev_err(dev,
+ "No IPC channel to communicate with wkup_m3!\n");
+ return -EIO;
+ }
+
+ /*
+ * Write a dummy message to the mailbox in order to trigger the RX
+ * interrupt to alert the M3 that data is available in the IPC
+ * registers. We must enable the IRQ here and disable it after in
+ * the RX callback to avoid multiple interrupts being received
+ * by the CM3.
+ */
+ ret = mbox_send_message(m3_ipc->mbox, &dummy_msg);
+ if (ret < 0) {
+ dev_err(dev, "%s: mbox_send_message() failed: %d\n",
+ __func__, ret);
+ return ret;
+ }
+
+ ret = wait_for_completion_timeout(&m3_ipc->sync_complete,
+ msecs_to_jiffies(500));
+ if (!ret) {
+ dev_err(dev, "MPU<->CM3 sync failure\n");
+ m3_ipc->state = M3_STATE_UNKNOWN;
+ return -EIO;
+ }
+
+ mbox_client_txdone(m3_ipc->mbox, 0);
+ return 0;
+}
+
+static int wkup_m3_ping_noirq(struct wkup_m3_ipc *m3_ipc)
+{
+ struct device *dev = m3_ipc->dev;
+ mbox_msg_t dummy_msg = 0;
+ int ret;
+
+ if (!m3_ipc->mbox) {
+ dev_err(dev,
+ "No IPC channel to communicate with wkup_m3!\n");
+ return -EIO;
+ }
+
+ ret = mbox_send_message(m3_ipc->mbox, &dummy_msg);
+ if (ret < 0) {
+ dev_err(dev, "%s: mbox_send_message() failed: %d\n",
+ __func__, ret);
+ return ret;
+ }
+
+ mbox_client_txdone(m3_ipc->mbox, 0);
+ return 0;
+}
+
+static int wkup_m3_is_available(struct wkup_m3_ipc *m3_ipc)
+{
+ return ((m3_ipc->state != M3_STATE_RESET) &&
+ (m3_ipc->state != M3_STATE_UNKNOWN));
+}
+
+/* Public functions */
+/**
+ * wkup_m3_set_mem_type - Pass wkup_m3 which type of memory is in use
+ * @mem_type: memory type value read directly from emif
+ *
+ * wkup_m3 must know what memory type is in use to properly suspend
+ * and resume.
+ */
+static void wkup_m3_set_mem_type(struct wkup_m3_ipc *m3_ipc, int mem_type)
+{
+ m3_ipc->mem_type = mem_type;
+}
+
+/**
+ * wkup_m3_set_resume_address - Pass wkup_m3 resume address
+ * @addr: Physical address from which resume code should execute
+ */
+static void wkup_m3_set_resume_address(struct wkup_m3_ipc *m3_ipc, void *addr)
+{
+ m3_ipc->resume_addr = (unsigned long)addr;
+}
+
+/**
+ * wkup_m3_request_pm_status - Retrieve wkup_m3 status code after suspend
+ *
+ * Returns code representing the status of a low power mode transition.
+ * 0 - Successful transition
+ * 1 - Failure to transition to low power state
+ */
+static int wkup_m3_request_pm_status(struct wkup_m3_ipc *m3_ipc)
+{
+ unsigned int i;
+ int val;
+
+ val = wkup_m3_ctrl_ipc_read(m3_ipc, 1);
+
+ i = M3_STATUS_RESP_MASK & val;
+ i >>= __ffs(M3_STATUS_RESP_MASK);
+
+ return i;
+}
+
+/**
+ * wkup_m3_prepare_low_power - Request preparation for transition to
+ * low power state
+ * @state: A kernel suspend state to enter, either MEM or STANDBY
+ *
+ * Returns 0 if preparation was successful, otherwise returns error code
+ */
+static int wkup_m3_prepare_low_power(struct wkup_m3_ipc *m3_ipc, int state)
+{
+ struct device *dev = m3_ipc->dev;
+ int m3_power_state;
+ int ret = 0;
+
+ if (!wkup_m3_is_available(m3_ipc))
+ return -ENODEV;
+
+ switch (state) {
+ case WKUP_M3_DEEPSLEEP:
+ m3_power_state = IPC_CMD_DS0;
+ break;
+ case WKUP_M3_STANDBY:
+ m3_power_state = IPC_CMD_STANDBY;
+ break;
+ case WKUP_M3_IDLE:
+ m3_power_state = IPC_CMD_IDLE;
+ break;
+ default:
+ return 1;
+ }
+
+ /* Program each required IPC register then write defaults to others */
+ wkup_m3_ctrl_ipc_write(m3_ipc, m3_ipc->resume_addr, 0);
+ wkup_m3_ctrl_ipc_write(m3_ipc, m3_power_state, 1);
+ wkup_m3_ctrl_ipc_write(m3_ipc, m3_ipc->mem_type, 4);
+
+ wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 2);
+ wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 3);
+ wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 5);
+ wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 6);
+ wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 7);
+
+ m3_ipc->state = M3_STATE_MSG_FOR_LP;
+
+ if (state == WKUP_M3_IDLE)
+ ret = wkup_m3_ping_noirq(m3_ipc);
+ else
+ ret = wkup_m3_ping(m3_ipc);
+
+ if (ret) {
+ dev_err(dev, "Unable to ping CM3\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+/**
+ * wkup_m3_finish_low_power - Return m3 to reset state
+ *
+ * Returns 0 if reset was successful, otherwise returns error code
+ */
+static int wkup_m3_finish_low_power(struct wkup_m3_ipc *m3_ipc)
+{
+ struct device *dev = m3_ipc->dev;
+ int ret = 0;
+
+ if (!wkup_m3_is_available(m3_ipc))
+ return -ENODEV;
+
+ wkup_m3_ctrl_ipc_write(m3_ipc, IPC_CMD_RESET, 1);
+ wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 2);
+
+ m3_ipc->state = M3_STATE_MSG_FOR_RESET;
+
+ ret = wkup_m3_ping(m3_ipc);
+ if (ret) {
+ dev_err(dev, "Unable to ping CM3\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static struct wkup_m3_ipc_ops ipc_ops = {
+ .set_mem_type = wkup_m3_set_mem_type,
+ .set_resume_address = wkup_m3_set_resume_address,
+ .prepare_low_power = wkup_m3_prepare_low_power,
+ .finish_low_power = wkup_m3_finish_low_power,
+ .request_pm_status = wkup_m3_request_pm_status,
+};
+
+/**
+ * wkup_m3_ipc_get - Return handle to wkup_m3_ipc
+ *
+ * Returns NULL if the wkup_m3 is not yet available, otherwise returns
+ * pointer to wkup_m3_ipc struct.
+ */
+struct wkup_m3_ipc *wkup_m3_ipc_get(void)
+{
+ if (m3_ipc_state)
+ get_device(m3_ipc_state->dev);
+ else
+ return NULL;
+
+ return m3_ipc_state;
+}
+EXPORT_SYMBOL_GPL(wkup_m3_ipc_get);
+
+/**
+ * wkup_m3_ipc_put - Free handle to wkup_m3_ipc returned from wkup_m3_ipc_get
+ * @m3_ipc: A pointer to wkup_m3_ipc struct returned by wkup_m3_ipc_get
+ */
+void wkup_m3_ipc_put(struct wkup_m3_ipc *m3_ipc)
+{
+ if (m3_ipc_state)
+ put_device(m3_ipc_state->dev);
+}
+EXPORT_SYMBOL_GPL(wkup_m3_ipc_put);
+
+static void wkup_m3_rproc_boot_thread(struct wkup_m3_ipc *m3_ipc)
+{
+ struct device *dev = m3_ipc->dev;
+ int ret;
+
+ wait_for_completion(&m3_ipc->rproc->firmware_loading_complete);
+
+ init_completion(&m3_ipc->sync_complete);
+
+ ret = rproc_boot(m3_ipc->rproc);
+ if (ret)
+ dev_err(dev, "rproc_boot failed\n");
+
+ do_exit(0);
+}
+
+static int wkup_m3_ipc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ int irq, ret;
+ phandle rproc_phandle;
+ struct rproc *m3_rproc;
+ struct resource *res;
+ struct task_struct *task;
+ struct wkup_m3_ipc *m3_ipc;
+
+ m3_ipc = devm_kzalloc(dev, sizeof(*m3_ipc), GFP_KERNEL);
+ if (!m3_ipc)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ m3_ipc->ipc_mem_base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(m3_ipc->ipc_mem_base)) {
+ dev_err(dev, "could not ioremap ipc_mem\n");
+ return PTR_ERR(m3_ipc->ipc_mem_base);
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (!irq) {
+ dev_err(&pdev->dev, "no irq resource\n");
+ return -ENXIO;
+ }
+
+ ret = devm_request_irq(dev, irq, wkup_m3_txev_handler,
+ 0, "wkup_m3_txev", m3_ipc);
+ if (ret) {
+ dev_err(dev, "request_irq failed\n");
+ return ret;
+ }
+
+ m3_ipc->mbox_client.dev = dev;
+ m3_ipc->mbox_client.tx_done = NULL;
+ m3_ipc->mbox_client.tx_prepare = NULL;
+ m3_ipc->mbox_client.rx_callback = NULL;
+ m3_ipc->mbox_client.tx_block = false;
+ m3_ipc->mbox_client.knows_txdone = false;
+
+ m3_ipc->mbox = mbox_request_channel(&m3_ipc->mbox_client, 0);
+
+ if (IS_ERR(m3_ipc->mbox)) {
+ dev_err(dev, "IPC Request for A8->M3 Channel failed! %ld\n",
+ PTR_ERR(m3_ipc->mbox));
+ return PTR_ERR(m3_ipc->mbox);
+ }
+
+ if (of_property_read_u32(dev->of_node, "ti,rproc", &rproc_phandle)) {
+ dev_err(&pdev->dev, "could not get rproc phandle\n");
+ ret = -ENODEV;
+ goto err_free_mbox;
+ }
+
+ m3_rproc = rproc_get_by_phandle(rproc_phandle);
+ if (!m3_rproc) {
+ dev_err(&pdev->dev, "could not get rproc handle\n");
+ ret = -EPROBE_DEFER;
+ goto err_free_mbox;
+ }
+
+ m3_ipc->rproc = m3_rproc;
+ m3_ipc->dev = dev;
+ m3_ipc->state = M3_STATE_RESET;
+
+ m3_ipc->ops = &ipc_ops;
+
+ /*
+ * Wait for firmware loading completion in a thread so we
+ * can boot the wkup_m3 as soon as it's ready without holding
+ * up kernel boot
+ */
+ task = kthread_run((void *)wkup_m3_rproc_boot_thread, m3_ipc,
+ "wkup_m3_rproc_loader");
+
+ if (IS_ERR(task)) {
+ dev_err(dev, "can't create rproc_boot thread\n");
+ goto err_put_rproc;
+ }
+
+ m3_ipc_state = m3_ipc;
+
+ return 0;
+
+err_put_rproc:
+ rproc_put(m3_rproc);
+err_free_mbox:
+ mbox_free_channel(m3_ipc->mbox);
+ return ret;
+}
+
+static int wkup_m3_ipc_remove(struct platform_device *pdev)
+{
+ mbox_free_channel(m3_ipc_state->mbox);
+
+ rproc_shutdown(m3_ipc_state->rproc);
+ rproc_put(m3_ipc_state->rproc);
+
+ m3_ipc_state = NULL;
+
+ return 0;
+}
+
+static const struct of_device_id wkup_m3_ipc_of_match[] = {
+ { .compatible = "ti,am3352-wkup-m3-ipc", },
+ { .compatible = "ti,am4372-wkup-m3-ipc", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, wkup_m3_ipc_of_match);
+
+static struct platform_driver wkup_m3_ipc_driver = {
+ .probe = wkup_m3_ipc_probe,
+ .remove = wkup_m3_ipc_remove,
+ .driver = {
+ .name = "wkup_m3_ipc",
+ .of_match_table = wkup_m3_ipc_of_match,
+ },
+};
+
+module_platform_driver(wkup_m3_ipc_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("wkup m3 remote processor ipc driver");
+MODULE_AUTHOR("Dave Gerlach <d-gerlach@ti.com>");
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index d27a0c6..39721ec 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1047,7 +1047,7 @@
say Y or M. Otherwise, say N.
config SERIAL_MSM
- bool "MSM on-chip serial port support"
+ tristate "MSM on-chip serial port support"
depends on ARCH_QCOM
select SERIAL_CORE
diff --git a/include/dt-bindings/power/raspberrypi-power.h b/include/dt-bindings/power/raspberrypi-power.h
new file mode 100644
index 0000000..b3ff8e0
--- /dev/null
+++ b/include/dt-bindings/power/raspberrypi-power.h
@@ -0,0 +1,41 @@
+/*
+ * Copyright © 2015 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _DT_BINDINGS_ARM_BCM2835_RPI_POWER_H
+#define _DT_BINDINGS_ARM_BCM2835_RPI_POWER_H
+
+/* These power domain indices are the firmware interface's indices
+ * minus one.
+ */
+#define RPI_POWER_DOMAIN_I2C0 0
+#define RPI_POWER_DOMAIN_I2C1 1
+#define RPI_POWER_DOMAIN_I2C2 2
+#define RPI_POWER_DOMAIN_VIDEO_SCALER 3
+#define RPI_POWER_DOMAIN_VPU1 4
+#define RPI_POWER_DOMAIN_HDMI 5
+#define RPI_POWER_DOMAIN_USB 6
+#define RPI_POWER_DOMAIN_VEC 7
+#define RPI_POWER_DOMAIN_JPEG 8
+#define RPI_POWER_DOMAIN_H264 9
+#define RPI_POWER_DOMAIN_V3D 10
+#define RPI_POWER_DOMAIN_ISP 11
+#define RPI_POWER_DOMAIN_UNICAM0 12
+#define RPI_POWER_DOMAIN_UNICAM1 13
+#define RPI_POWER_DOMAIN_CCP2RX 14
+#define RPI_POWER_DOMAIN_CSI2 15
+#define RPI_POWER_DOMAIN_CPI 16
+#define RPI_POWER_DOMAIN_DSI0 17
+#define RPI_POWER_DOMAIN_DSI1 18
+#define RPI_POWER_DOMAIN_TRANSPOSER 19
+#define RPI_POWER_DOMAIN_CCP2TX 20
+#define RPI_POWER_DOMAIN_CDP 21
+#define RPI_POWER_DOMAIN_ARM 22
+
+#define RPI_POWER_DOMAIN_COUNT 23
+
+#endif /* _DT_BINDINGS_ARM_BCM2835_RPI_POWER_H */
diff --git a/include/dt-bindings/reset/hisi,hi6220-resets.h b/include/dt-bindings/reset/hisi,hi6220-resets.h
new file mode 100644
index 0000000..ca08a7e
--- /dev/null
+++ b/include/dt-bindings/reset/hisi,hi6220-resets.h
@@ -0,0 +1,67 @@
+/**
+ * This header provides index for the reset controller
+ * based on hi6220 SoC.
+ */
+#ifndef _DT_BINDINGS_RESET_CONTROLLER_HI6220
+#define _DT_BINDINGS_RESET_CONTROLLER_HI6220
+
+#define PERIPH_RSTDIS0_MMC0 0x000
+#define PERIPH_RSTDIS0_MMC1 0x001
+#define PERIPH_RSTDIS0_MMC2 0x002
+#define PERIPH_RSTDIS0_NANDC 0x003
+#define PERIPH_RSTDIS0_USBOTG_BUS 0x004
+#define PERIPH_RSTDIS0_POR_PICOPHY 0x005
+#define PERIPH_RSTDIS0_USBOTG 0x006
+#define PERIPH_RSTDIS0_USBOTG_32K 0x007
+#define PERIPH_RSTDIS1_HIFI 0x100
+#define PERIPH_RSTDIS1_DIGACODEC 0x105
+#define PERIPH_RSTEN2_IPF 0x200
+#define PERIPH_RSTEN2_SOCP 0x201
+#define PERIPH_RSTEN2_DMAC 0x202
+#define PERIPH_RSTEN2_SECENG 0x203
+#define PERIPH_RSTEN2_ABB 0x204
+#define PERIPH_RSTEN2_HPM0 0x205
+#define PERIPH_RSTEN2_HPM1 0x206
+#define PERIPH_RSTEN2_HPM2 0x207
+#define PERIPH_RSTEN2_HPM3 0x208
+#define PERIPH_RSTEN3_CSSYS 0x300
+#define PERIPH_RSTEN3_I2C0 0x301
+#define PERIPH_RSTEN3_I2C1 0x302
+#define PERIPH_RSTEN3_I2C2 0x303
+#define PERIPH_RSTEN3_I2C3 0x304
+#define PERIPH_RSTEN3_UART1 0x305
+#define PERIPH_RSTEN3_UART2 0x306
+#define PERIPH_RSTEN3_UART3 0x307
+#define PERIPH_RSTEN3_UART4 0x308
+#define PERIPH_RSTEN3_SSP 0x309
+#define PERIPH_RSTEN3_PWM 0x30a
+#define PERIPH_RSTEN3_BLPWM 0x30b
+#define PERIPH_RSTEN3_TSENSOR 0x30c
+#define PERIPH_RSTEN3_DAPB 0x312
+#define PERIPH_RSTEN3_HKADC 0x313
+#define PERIPH_RSTEN3_CODEC_SSI 0x314
+#define PERIPH_RSTEN3_PMUSSI1 0x316
+#define PERIPH_RSTEN8_RS0 0x400
+#define PERIPH_RSTEN8_RS2 0x401
+#define PERIPH_RSTEN8_RS3 0x402
+#define PERIPH_RSTEN8_MS0 0x403
+#define PERIPH_RSTEN8_MS2 0x405
+#define PERIPH_RSTEN8_XG2RAM0 0x406
+#define PERIPH_RSTEN8_X2SRAM_TZMA 0x407
+#define PERIPH_RSTEN8_SRAM 0x408
+#define PERIPH_RSTEN8_HARQ 0x40a
+#define PERIPH_RSTEN8_DDRC 0x40c
+#define PERIPH_RSTEN8_DDRC_APB 0x40d
+#define PERIPH_RSTEN8_DDRPACK_APB 0x40e
+#define PERIPH_RSTEN8_DDRT 0x411
+#define PERIPH_RSDIST9_CARM_DAP 0x500
+#define PERIPH_RSDIST9_CARM_ATB 0x501
+#define PERIPH_RSDIST9_CARM_LBUS 0x502
+#define PERIPH_RSDIST9_CARM_POR 0x503
+#define PERIPH_RSDIST9_CARM_CORE 0x504
+#define PERIPH_RSDIST9_CARM_DBG 0x505
+#define PERIPH_RSDIST9_CARM_L2 0x506
+#define PERIPH_RSDIST9_CARM_SOCDBG 0x507
+#define PERIPH_RSDIST9_CARM_ETM 0x508
+
+#endif /*_DT_BINDINGS_RESET_CONTROLLER_HI6220*/
diff --git a/include/dt-bindings/reset/stih407-resets.h b/include/dt-bindings/reset/stih407-resets.h
index 02d4328..4ab3a1c 100644
--- a/include/dt-bindings/reset/stih407-resets.h
+++ b/include/dt-bindings/reset/stih407-resets.h
@@ -52,6 +52,10 @@
#define STIH407_KEYSCAN_SOFTRESET 26
#define STIH407_USB2_PORT0_SOFTRESET 27
#define STIH407_USB2_PORT1_SOFTRESET 28
+#define STIH407_ST231_AUD_SOFTRESET 29
+#define STIH407_ST231_DMU_SOFTRESET 30
+#define STIH407_ST231_GP0_SOFTRESET 31
+#define STIH407_ST231_GP1_SOFTRESET 32
/* Picophy reset defines */
#define STIH407_PICOPHY0_RESET 0
diff --git a/include/linux/reset.h b/include/linux/reset.h
index 7f65f9c..c4c097d 100644
--- a/include/linux/reset.h
+++ b/include/linux/reset.h
@@ -38,6 +38,9 @@
struct reset_control *of_reset_control_get(struct device_node *node,
const char *id);
+struct reset_control *of_reset_control_get_by_index(
+ struct device_node *node, int index);
+
#else
static inline int reset_control_reset(struct reset_control *rstc)
@@ -71,7 +74,7 @@
static inline int device_reset_optional(struct device *dev)
{
- return -ENOSYS;
+ return -ENOTSUPP;
}
static inline struct reset_control *__must_check reset_control_get(
@@ -91,19 +94,25 @@
static inline struct reset_control *reset_control_get_optional(
struct device *dev, const char *id)
{
- return ERR_PTR(-ENOSYS);
+ return ERR_PTR(-ENOTSUPP);
}
static inline struct reset_control *devm_reset_control_get_optional(
struct device *dev, const char *id)
{
- return ERR_PTR(-ENOSYS);
+ return ERR_PTR(-ENOTSUPP);
}
static inline struct reset_control *of_reset_control_get(
struct device_node *node, const char *id)
{
- return ERR_PTR(-ENOSYS);
+ return ERR_PTR(-ENOTSUPP);
+}
+
+static inline struct reset_control *of_reset_control_get_by_index(
+ struct device_node *node, int index)
+{
+ return ERR_PTR(-ENOTSUPP);
}
#endif /* CONFIG_RESET_CONTROLLER */
diff --git a/include/linux/soc/qcom/smem_state.h b/include/linux/soc/qcom/smem_state.h
new file mode 100644
index 0000000..f35e151
--- /dev/null
+++ b/include/linux/soc/qcom/smem_state.h
@@ -0,0 +1,18 @@
+#ifndef __QCOM_SMEM_STATE__
+#define __QCOM_SMEM_STATE__
+
+struct qcom_smem_state;
+
+struct qcom_smem_state_ops {
+ int (*update_bits)(void *, u32, u32);
+};
+
+struct qcom_smem_state *qcom_smem_state_get(struct device *dev, const char *con_id, unsigned *bit);
+void qcom_smem_state_put(struct qcom_smem_state *);
+
+int qcom_smem_state_update_bits(struct qcom_smem_state *state, u32 mask, u32 value);
+
+struct qcom_smem_state *qcom_smem_state_register(struct device_node *of_node, const struct qcom_smem_state_ops *ops, void *data);
+void qcom_smem_state_unregister(struct qcom_smem_state *state);
+
+#endif
diff --git a/include/linux/wkup_m3_ipc.h b/include/linux/wkup_m3_ipc.h
new file mode 100644
index 0000000..d6ba7d3
--- /dev/null
+++ b/include/linux/wkup_m3_ipc.h
@@ -0,0 +1,55 @@
+/*
+ * TI Wakeup M3 for AMx3 SoCs Power Management Routines
+ *
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ * Dave Gerlach <d-gerlach@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _LINUX_WKUP_M3_IPC_H
+#define _LINUX_WKUP_M3_IPC_H
+
+#define WKUP_M3_DEEPSLEEP 1
+#define WKUP_M3_STANDBY 2
+#define WKUP_M3_IDLE 3
+
+#include <linux/mailbox_client.h>
+
+struct wkup_m3_ipc_ops;
+
+struct wkup_m3_ipc {
+ struct rproc *rproc;
+
+ void __iomem *ipc_mem_base;
+ struct device *dev;
+
+ int mem_type;
+ unsigned long resume_addr;
+ int state;
+
+ struct completion sync_complete;
+ struct mbox_client mbox_client;
+ struct mbox_chan *mbox;
+
+ struct wkup_m3_ipc_ops *ops;
+};
+
+struct wkup_m3_ipc_ops {
+ void (*set_mem_type)(struct wkup_m3_ipc *m3_ipc, int mem_type);
+ void (*set_resume_address)(struct wkup_m3_ipc *m3_ipc, void *addr);
+ int (*prepare_low_power)(struct wkup_m3_ipc *m3_ipc, int state);
+ int (*finish_low_power)(struct wkup_m3_ipc *m3_ipc);
+ int (*request_pm_status)(struct wkup_m3_ipc *m3_ipc);
+};
+
+struct wkup_m3_ipc *wkup_m3_ipc_get(void);
+void wkup_m3_ipc_put(struct wkup_m3_ipc *m3_ipc);
+#endif /* _LINUX_WKUP_M3_IPC_H */
diff --git a/include/soc/bcm2835/raspberrypi-firmware.h b/include/soc/bcm2835/raspberrypi-firmware.h
index c07d74a..3fb3571 100644
--- a/include/soc/bcm2835/raspberrypi-firmware.h
+++ b/include/soc/bcm2835/raspberrypi-firmware.h
@@ -72,10 +72,12 @@
RPI_FIRMWARE_SET_ENABLE_QPU = 0x00030012,
RPI_FIRMWARE_GET_DISPMANX_RESOURCE_MEM_HANDLE = 0x00030014,
RPI_FIRMWARE_GET_EDID_BLOCK = 0x00030020,
+ RPI_FIRMWARE_GET_DOMAIN_STATE = 0x00030030,
RPI_FIRMWARE_SET_CLOCK_STATE = 0x00038001,
RPI_FIRMWARE_SET_CLOCK_RATE = 0x00038002,
RPI_FIRMWARE_SET_VOLTAGE = 0x00038003,
RPI_FIRMWARE_SET_TURBO = 0x00038009,
+ RPI_FIRMWARE_SET_DOMAIN_STATE = 0x00038030,
/* Dispmanx TAGS */
RPI_FIRMWARE_FRAMEBUFFER_ALLOCATE = 0x00040001,