Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 1 | # This file allows user to override the factory |
| 2 | # defaults for the WLAN Driver |
| 3 | |
| 4 | ############################################# |
| 5 | # STA related general configurations |
| 6 | ############################################# |
| 7 | # Assigned MAC Addresses - This will be used until NV items are in place |
| 8 | # Each byte of MAC address is represented in Hex format as XX |
| 9 | Intf0MacAddress=000AF58989FF |
| 10 | Intf1MacAddress=000AF58989FE |
| 11 | Intf2MacAddress=000AF58989FD |
| 12 | Intf3MacAddress=000AF58989FC |
| 13 | |
| 14 | #Channel Bonding |
| 15 | gChannelBondingMode5GHz=1 |
| 16 | gChannelBondingMode24GHz=0 |
| 17 | |
| 18 | #Enable Keep alive with non-zero period value |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 19 | gStaKeepAlivePeriod=60 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 20 | |
| 21 | # Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) |
| 22 | gVhtMpduLen=2 |
| 23 | |
| 24 | # 0 for OLPC 1 for CLPC and SCPC |
| 25 | gEnableCloseLoop=1 |
| 26 | |
| 27 | ImplicitQosIsEnabled=0 |
| 28 | |
| 29 | # Enable Tx beamforming in VHT20MHz |
| 30 | # Valid values are 0,1. If commented out, the default value is 0. |
| 31 | # 0=disable, 1=enable |
| 32 | gEnableTxBFin20MHz=1 |
| 33 | |
| 34 | #Enable/Disable SU Tx beamformer support. |
Kumar Anand | e23d4f4 | 2018-08-14 12:19:31 -0700 | [diff] [blame] | 35 | gEnableTxSUBeamformer=0 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 36 | |
| 37 | # 1=enable tx STBC; 0=disable |
| 38 | gEnableTXSTBC=1 |
| 39 | |
| 40 | # 1=enable STBC; 0=disable STBC |
| 41 | gEnableRXSTBC=1 |
| 42 | |
| 43 | # 1=enable rx LDPC; 0=disable |
| 44 | gEnableRXLDPC=1 |
| 45 | |
| 46 | # Flag to allow STA send AddTspec even when ACM is Off |
| 47 | gAddTSWhenACMIsOff=1 |
| 48 | |
| 49 | # RTS threshold |
| 50 | RTSThreshold=1048576 |
| 51 | |
| 52 | # 802.11d support |
| 53 | g11dSupportEnabled=0 |
| 54 | |
| 55 | |
| 56 | # Phy Mode (auto, b, g, n, etc) |
| 57 | # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac |
| 58 | # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only |
| 59 | # 7 = 11b only 8 = 11ac only. |
| 60 | gDot11Mode=0 |
| 61 | |
| 62 | # Enable Rx handling options |
| 63 | # Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium) |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 64 | # Rx_thread + NAPI = 5 |
| 65 | rx_mode=5 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 66 | |
| 67 | #Enable VHT on 2.4Ghz |
| 68 | gEnableVhtFor24GHzBand=1 |
| 69 | |
| 70 | # Regulatory Setting; 0=STRICT; 1=CUSTOM |
| 71 | gRegulatoryChangeCountry=1 |
| 72 | |
| 73 | # userspace country code setting shld take priority |
| 74 | gCountryCodePriority=1 |
| 75 | |
| 76 | # Enable/Disable LPASS support |
| 77 | # 0 to disable, 1 to enable |
| 78 | gEnableLpassSupport=1 |
| 79 | |
| 80 | # Enable(1)/Disable(0) SIFS burst |
| 81 | gEnableSifsBurst=1 |
| 82 | |
| 83 | # Tx Chain Mask for CCK |
| 84 | gCckChainMaskEnable=1 |
| 85 | |
| 86 | # Tx Chain Mask for 1SS |
| 87 | gTxChainMask1ss=0 |
| 88 | |
| 89 | # TPC power |
| 90 | gSelfGenFrmPwr=3 |
| 91 | |
Srinivas Girigowda | 2f803ed | 2017-11-20 18:44:43 -0800 | [diff] [blame] | 92 | gReportMaxLinkSpeed=0 |
| 93 | |
Srinivas Girigowda | 5abc707 | 2018-04-11 07:26:28 -0700 | [diff] [blame] | 94 | enable_mac_provision=1 |
| 95 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 96 | ################ NAN feature set start ################### |
| 97 | # Enable or Disable NAN |
| 98 | # 1=Enable (default), 0=Disable |
| 99 | gEnableNanSupport=1 |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 100 | genable_nan_datapath=1 |
| 101 | gnan_datapath_ndi_channel=6 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 102 | ################ NAN feature set end ##################### |
| 103 | |
| 104 | gIgnorePeerHTopMode=1 |
| 105 | gIgnorePeerErpInfo=1 |
| 106 | |
| 107 | # 802.11n Protection flag |
| 108 | gEnableApProt=1 |
| 109 | |
| 110 | # Fixed Rate |
| 111 | gFixedRate=0 |
| 112 | |
| 113 | # Intra-BSS forward |
| 114 | gDisableIntraBssFwd=0 |
| 115 | |
| 116 | # WMM Enable/Disable |
| 117 | WmmIsEnabled=0 |
| 118 | |
| 119 | # 802.11h support |
| 120 | g11hSupportEnabled=1 |
| 121 | |
| 122 | #Short Guard Interval Enable/disable |
| 123 | gShortGI20Mhz=1 |
| 124 | gShortGI40Mhz=1 |
| 125 | |
| 126 | #Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec |
| 127 | gWlanAutoShutdown=0 |
| 128 | |
| 129 | #Preferred band (both or 2.4 only or 5 only) |
| 130 | BandCapability=0 |
| 131 | |
| 132 | gVhtChannelWidth=2 |
| 133 | |
| 134 | # Enable Tx beamforming |
| 135 | gTxBFEnable=1 |
| 136 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 137 | # Scan Timing Parameters |
| 138 | # gPassiveMaxChannelTime=110 |
| 139 | # gPassiveMinChannelTime=60 |
| 140 | gActiveMaxChannelTime=40 |
| 141 | gActiveMinChannelTime=20 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 142 | |
| 143 | #If set to 0, MCC is not allowed. |
| 144 | gEnableMCCMode=1 |
| 145 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 146 | # MCC to SCC Switch mode: |
| 147 | # 0-Disable |
| 148 | # 1-Enable |
| 149 | # 2-Force SCC if same band, with SAP restart |
| 150 | # 3-Force SCC if same band, without SAP restart by sending (E)CSA |
| 151 | # 4-Force SCC if same band (or) use SAP mandatory channel for DBS, |
| 152 | # without SAP restart by sending (E)CSA |
| 153 | gWlanMccToSccSwitchMode = 3 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 154 | |
| 155 | # Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k) |
| 156 | gVhtAmpduLenExponent=7 |
| 157 | |
| 158 | # Maximum number of concurrent connections |
| 159 | gMaxConcurrentActiveSessions=3 |
| 160 | |
| 161 | # Radar PRI multiplier |
| 162 | gDFSradarMappingPriMultiplier=4 |
| 163 | |
| 164 | # Enable or Disable Multi-user MIMO |
| 165 | # 1=Enable (default), 0=Disable |
| 166 | gEnableMuBformee=1 |
| 167 | |
| 168 | # Enable to check FW hash if secure FW feature is enabled. It's for defconfig |
| 169 | # builds only since it will be ignored in performance/release builds. |
| 170 | gEnableFWHashCheck=1 |
| 171 | |
| 172 | # Enable or Disable MCC Adaptive Scheduler at the FW |
| 173 | # 1=Enable (default), 0=Disable |
| 174 | gEnableMCCAdaptiveScheduler=1 |
| 175 | |
| 176 | # Disable/Enable GreenAP |
| 177 | # 0 to disable, 1 to enable, default: 1 |
| 178 | gEnableGreenAp=0 |
| 179 | |
| 180 | ################ Datapath feature set Begin ################ |
| 181 | # Bus bandwidth threshold values in terms of number of packets |
| 182 | gBusBandwidthHighThreshold=2000 |
| 183 | gBusBandwidthMediumThreshold=500 |
| 184 | gBusBandwidthLowThreshold=150 |
| 185 | |
| 186 | # Bus bandwidth compute timeout value in ms |
| 187 | gBusBandwidthComputeInterval=100 |
| 188 | |
| 189 | # VHT Tx/Rx MCS values |
| 190 | # Valid values are 0,1,2. If commented out, the default value is 0. |
| 191 | # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| 192 | gVhtRxMCS=2 |
| 193 | gVhtTxMCS=2 |
| 194 | |
| 195 | # VHT Tx/Rx MCS values for 2x2 |
| 196 | # Valid values are 0,1,2. If commented out, the default value is 0. |
| 197 | # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| 198 | gEnable2x2=1 |
| 199 | gVhtRxMCS2x2=2 |
| 200 | gVhtTxMCS2x2=2 |
| 201 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 202 | # Enable/Disable RX full reorder offload |
| 203 | gReorderOffloadSupported=1 |
| 204 | |
| 205 | # Enable CE classification |
| 206 | # 1 - enable(default) 0 - disable |
| 207 | gCEClassifyEnable=1 |
| 208 | |
| 209 | # Enable(Tx) fastpath for data traffic. |
| 210 | # 1 - enable(default) 0 - disable |
| 211 | gEnableFastPath=1 |
| 212 | |
| 213 | # This flag enables IP, TCP and UDP checksum offload |
| 214 | # 1 - enable(default) 0 - disable |
| 215 | gEnableIpTcpUdpChecksumOffload=1 |
| 216 | |
| 217 | # Enable TCP Segmentation Offload |
| 218 | # 1 - enable 0 - disable |
| 219 | TSOEnable=1 |
| 220 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 221 | # Enable Generic Receive Offload |
| 222 | # LRO and GRO are exclusive to each other |
| 223 | # LRO support is deprecated on latest 4.9(SDM845) kernel |
| 224 | GROEnable=1 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 225 | |
| 226 | # Enable HT MPDU Density |
| 227 | # 4 for 2 micro sec |
| 228 | ght_mpdu_density=4 |
| 229 | |
| 230 | # Enable flow steering to enable multiple CEs for Rx flows. |
| 231 | # Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs. |
| 232 | # Parallel Rx paths. |
| 233 | # 1 - enable 0 - disable(default) |
| 234 | gEnableFlowSteering=1 |
| 235 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 236 | ce_service_max_yield_time=500 |
| 237 | ce_service_max_rx_ind_flush=1 |
| 238 | maxMSDUsPerRxInd=8 |
| 239 | |
Srinivas Girigowda | 5abc707 | 2018-04-11 07:26:28 -0700 | [diff] [blame] | 240 | gEnableDataStallDetection=0 |
| 241 | |
| 242 | gTcpLimitOutputEnable=0 |
| 243 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 244 | ################ Datapath feature set End ################ |
| 245 | |
| 246 | ############################################# |
| 247 | # SCAN related configurations |
| 248 | ############################################# |
| 249 | # Enable/Disable Idle Scan |
| 250 | gEnableIdleScan=0 |
| 251 | |
| 252 | #Enable Scan Results Aging based on timer |
| 253 | #Timer value is in seconds |
| 254 | #If Set to 0 it will not enable the feature |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 255 | gScanAgingTime=30 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 256 | |
| 257 | #Enable Scan Results Aging based on number of scans |
| 258 | gScanResultAgeCount=1 |
| 259 | |
| 260 | #Enable thermal mitigation |
| 261 | gThermalMitigationEnable=0 |
| 262 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 263 | #Maximum Channel time in msec |
| 264 | gMaxMediumTime=6000 |
| 265 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 266 | gPNOScanSupport=1 |
| 267 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 268 | # Enable or Disable Extended Scan (GScan) |
| 269 | # 1=Enable (default), 0=Disable |
| 270 | gExtScanEnable=1 |
| 271 | |
| 272 | #If set will start with active scan after driver load, otherwise will start with |
| 273 | #passive scan to find out the domain |
| 274 | gEnableBypass11d=1 |
| 275 | |
| 276 | #If set to 0, will not scan DFS channels |
| 277 | gEnableDFSChnlScan=1 |
| 278 | |
| 279 | #Maxium Channel time in msec |
| 280 | gMaxMediumTime = 6000 |
| 281 | |
| 282 | adaptive_dwell_mode_enabled=1 |
| 283 | |
| 284 | hostscan_adaptive_dwell_mode=1 |
| 285 | |
| 286 | adapt_dwell_lpf_weight=80 |
| 287 | |
| 288 | adapt_dwell_wifi_act_threshold=10 |
| 289 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 290 | # Enable or disable Probe Req Information Element whitelist. When enabled, IEs corresponding to bits |
| 291 | # set in bitmaps are allowed in probe request, all others removed while device is unassociated |
| 292 | # with an AP |
| 293 | # 1=Enable, 0=Disable (default) |
| 294 | g_enable_probereq_whitelist_ies=1 |
| 295 | |
| 296 | # ie bitmap examples: <bitmap_name>=<value> [<Allowed Information elements>] |
| 297 | # g_probe_req_ie_bitmap_0=0x80000009 #[0, 3, 31] |
| 298 | # g_probe_req_ie_bitmap_0=0x00000000 #[] (default) |
| 299 | # g_probe_req_ie_bitmap_1=0x80000009 #[32, 35, 63] |
| 300 | g_probe_req_ie_bitmap_0=0x0000000B |
Kumar Anand | c7f62a5 | 2019-06-14 13:14:31 -0700 | [diff] [blame] | 301 | g_probe_req_ie_bitmap_1=0x00040000 |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 302 | # g_probe_req_ie_bitmap_2=0x00000000 |
| 303 | # g_probe_req_ie_bitmap_3=0x00000000 |
| 304 | # g_probe_req_ie_bitmap_4=0x00000000 |
| 305 | # g_probe_req_ie_bitmap_5=0x00000000 |
Srinivas Girigowda | 5abc707 | 2018-04-11 07:26:28 -0700 | [diff] [blame] | 306 | g_probe_req_ie_bitmap_6=0x20000000 |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 307 | # g_probe_req_ie_bitmap_7=0x00000000 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 308 | |
Srinivas Girigowda | 11f0e72 | 2018-05-16 18:08:06 -0700 | [diff] [blame] | 309 | gProbeReqOUIs=0050F208 |
| 310 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 311 | ############################################# |
| 312 | # Power related configurations |
| 313 | ############################################# |
| 314 | # Enable IMPS or not |
| 315 | gEnableImps=1 |
| 316 | |
| 317 | # Enable BMPS or not |
| 318 | gEnableBmps=1 |
| 319 | |
| 320 | # Increase sleep duration (seconds) during IMPS |
| 321 | # 0 implies no periodic wake up from IMPS. Periodic wakeup is |
| 322 | # unnecessary if Idle Scan is disabled. |
| 323 | gImpsModSleepTime=0 |
| 324 | |
| 325 | # UAPSD service interval for VO,VI, BE, BK traffic |
| 326 | InfraUapsdVoSrvIntv=0 |
| 327 | InfraUapsdViSrvIntv=0 |
| 328 | InfraUapsdBeSrvIntv=0 |
| 329 | InfraUapsdBkSrvIntv=0 |
| 330 | |
| 331 | # Enable suspend or not |
| 332 | # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter |
| 333 | gEnableSuspend=3 |
| 334 | |
| 335 | #Enable Power Save offload |
| 336 | gEnablePowerSaveOffload=2 |
| 337 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 338 | #Enable Power saving mechanism Based on Android Framework |
| 339 | #If set to 0 Driver internally control the Power saving mechanism |
| 340 | #If set to 1 Android Framwrok control the Power saving mechanism |
| 341 | isAndroidPsEn=0 |
| 342 | |
| 343 | beaconEarlyTerminationWakeInterval=3 |
| 344 | |
| 345 | #Data Inactivity Timeout when in powersave (in ms) |
| 346 | gDataInactivityTimeout=200 |
| 347 | |
| 348 | # Inactivity time (in ms) to end TX Service Period while in IBSS power save mode |
| 349 | gIbssTxSpEndInactivityTime=10 |
| 350 | |
| 351 | gEnableModulatedDTIM=2 |
| 352 | gMaxLIModulatedDTIM=6 |
| 353 | |
| 354 | ############################################# |
| 355 | # Roaming related configurations |
| 356 | ############################################# |
| 357 | # CSR Roaming Enable(1) Disable(0) |
| 358 | gRoamingTime=0 |
| 359 | |
| 360 | # ESE Support and fast transition |
| 361 | EseEnabled=1 |
| 362 | |
| 363 | gNeighborLookupThreshold=76 |
| 364 | gNeighborReassocThreshold=81 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 365 | gNeighborScanChannelMinTime=20 |
| 366 | gNeighborScanChannelMaxTime=30 |
| 367 | gMaxNeighborReqTries=3 |
| 368 | |
| 369 | # To enable, set gRoamIntraBand=1 (Roaming within band) |
| 370 | # To disable, set gRoamIntraBand=0 (Roaming across band) |
| 371 | gRoamIntraBand=0 |
| 372 | |
| 373 | # Legacy (non-ESE, non-802.11r) Fast Roaming Support |
| 374 | # To enable, set FastRoamEnabled=1 |
| 375 | # To disable, set FastRoamEnabled=0 |
| 376 | FastRoamEnabled=1 |
| 377 | |
| 378 | #Check if the AP to which we are roaming is better than current AP in terms of RSSI. |
| 379 | #Checking is disabled if set to Zero.Otherwise it will use this value as to how better |
| 380 | #the RSSI of the new/roamable AP should be for roaming |
| 381 | RoamRssiDiff=3 |
| 382 | |
| 383 | # If the RSSI of any available candidate is better than currently associated |
| 384 | # AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without |
| 385 | # registering for reassoc threshold). |
| 386 | # NOTE: Value of 0 means that we would register for reassoc threshold. |
| 387 | gImmediateRoamRssiDiff=10 |
| 388 | |
| 389 | # 802.11K support |
| 390 | gRrmEnable=1 |
| 391 | gRrmOperChanMax=8 |
| 392 | gRrmNonOperChanMax=8 |
| 393 | |
| 394 | gEnableFastRoamInConcurrency=1 |
| 395 | |
| 396 | # Enable/Disable Roaming Offload Support (a.k.a Key Management Offload) |
| 397 | # 0 to disable, 1 to enable |
| 398 | gRoamOffloadEnabled=1 |
| 399 | |
| 400 | gAllowDFSChannelRoam=1 |
| 401 | |
Srinivas Girigowda | 5abc707 | 2018-04-11 07:26:28 -0700 | [diff] [blame] | 402 | gLFRSubnetDetectionEnable=0 |
| 403 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 404 | ############################################# |
| 405 | # Offload related configurations |
| 406 | ############################################# |
| 407 | # Beacon filtering frequency (unit in beacon intervals) |
| 408 | gNthBeaconFilter=50 |
| 409 | |
| 410 | # Enable WAPI or not |
| 411 | # WAPIIsEnabled=0 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 412 | |
| 413 | #Flag to enable HostARPOffload feature or not |
| 414 | hostArpOffload=1 |
| 415 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 416 | #Flag to enable HostNSOffload feature or not |
| 417 | hostNSOffload=1 |
| 418 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 419 | # controlling the following offload patterns |
| 420 | # through ini parameter. Default value is 1 |
| 421 | # to disable set it to zero. ssdp = 0 |
| 422 | # Setup multicast pattern for mDNS 224.0.0.251, |
| 423 | # SSDP 239.255.255.250 and LLMNR 224.0.0.252 |
| 424 | ssdp = 0 |
| 425 | |
| 426 | #Enable MC address filtering offload |
| 427 | gMCAddrListEnable=1 |
| 428 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 429 | #Enable Active mode offload |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 430 | gActiveModeOffload=1 |
| 431 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 432 | #Enable Active mode offload |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 433 | gEnableActiveModeOffload=1 |
| 434 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 435 | #Enable APF in Active mode |
| 436 | gActiveUcBpfMode=2 |
| 437 | gActiveMcBcBpfMode=1 |
| 438 | |
| 439 | #HW CCE Filter mode |
| 440 | gHwFilterMode=0 |
| 441 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 442 | # WOW Enable/Disable. |
| 443 | # 0 - Disable both magic pattern match and pattern byte match. |
| 444 | # 1 - Enable magic pattern match on all interfaces. |
| 445 | # 2 - Enable pattern byte match on all interfaces. |
| 446 | # 3 - Enable both magic patter and pattern byte match on all interfaces. |
| 447 | # Default value of gEnableWoW is 3. |
| 448 | # gEnableWoW=0 |
| 449 | |
Srinivas Girigowda | 5abc707 | 2018-04-11 07:26:28 -0700 | [diff] [blame] | 450 | 11k_offload_enable_bitmask=0 |
| 451 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 452 | |
| 453 | ############################################# |
| 454 | # Logging related configurations |
| 455 | ############################################# |
| 456 | gEnableLogp=1 |
| 457 | |
| 458 | gEnableSelfRecovery=1 |
| 459 | |
| 460 | #Enable firmware log |
| 461 | gEnablefwlog=1 |
| 462 | # Additional firmware log levels |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 463 | gFwDebugLogLevel=3 |
| 464 | gFwDebugModuleLoglevel=2,1,3,1,5,1,9,1,13,1,14,1,18,1,19,1,26,1,28,1,29,1,31,1,36,1,38,1,46,1,47,1,50,1,52,1,53,1,56,1,60,1,61,1,4,1 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 465 | |
| 466 | #Enable firmware uart print |
| 467 | gEnablefwprint=0 |
| 468 | |
| 469 | ############################################# |
| 470 | # TDLS related configurations |
| 471 | ############################################# |
| 472 | # Enable support for TDLS |
| 473 | # 0 - disable |
| 474 | # 1 - enable |
| 475 | gEnableTDLSSupport=1 |
| 476 | |
| 477 | # Enable support for Implicit Trigger of TDLS. That is, wlan driver shall |
| 478 | # initiate TDLS Discovery towards a peer whenever setup criteria (throughput |
| 479 | # and RSSI) is met and then will initiate teardown when teardown criteria |
| 480 | # (idle packet count and RSSI) is met. |
| 481 | # 0 - disable |
| 482 | # 1 - enable |
| 483 | gEnableTDLSImplicitTrigger=1 |
| 484 | |
| 485 | # Enable TDLS External Control. That is, user space application has to |
| 486 | # first configure a peer MAC in wlan driver towards which TDLS is desired. |
| 487 | # Device will establish TDLS only towards those configured peers whenever |
| 488 | # TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS |
| 489 | # when teardown criteria (idle packet count and RSSI) is met. However, |
| 490 | # device will accept TDLS connection if it is initiated from any other peer, |
| 491 | # even if that peer is not configured. |
| 492 | # 0 - disable |
| 493 | # 1 - enable |
| 494 | # For TDLS External Control, Implicit Trigger must also be enabled. |
| 495 | gTDLSExternalControl=1 |
| 496 | |
| 497 | # Enable support for TDLS off-channel operation |
| 498 | # 0 - disable |
| 499 | # 1 - enable |
| 500 | # TDLS off-channel operation will be invoked when there is only one |
| 501 | # TDLS connection. |
Sunil Ravi | 10d818d | 2020-07-21 10:14:09 -0700 | [diff] [blame] | 502 | gEnableTDLSOffChannel=0 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 503 | |
| 504 | gEnableTDLSScan=1 |
| 505 | gTDLSTxPacketThreshold=10 |
| 506 | gTDLSIdlePacketThreshold=1 |
| 507 | |
| 508 | ############################################# |
| 509 | # P2P related configurations |
| 510 | ############################################# |
| 511 | #P2P Listen offload |
| 512 | gEnableP2pListenOffload=1 |
| 513 | |
| 514 | #Enable or Disable p2p device address administered |
| 515 | isP2pDeviceAddrAdministrated=0 |
| 516 | |
| 517 | #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). |
| 518 | #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) |
| 519 | #For both active and power save clients. |
| 520 | |
| 521 | #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. |
| 522 | #If doesn't honor for 5 seconds then DUT remove client. |
| 523 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 524 | # chain mask related params |
| 525 | # |
| 526 | # Set txchainmask and rxchainmask |
| 527 | # These parameters are used only if gEnable2x2 is 0 |
| 528 | # Valid values are 1,2 |
| 529 | # Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. |
| 530 | # Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. |
| 531 | gSetTxChainmask1x1=1 |
| 532 | gSetRxChainmask1x1=1 |
| 533 | |
| 534 | # Following parameters are for test purpose only and when set will |
| 535 | # configure tx and rx per band chain mask. These parameters will |
| 536 | # take effect only when: |
| 537 | # gEnable2x2=0 |
| 538 | # gDualMacFeatureDisable=1 |
| 539 | # gSetTxChainmask1x1=0 |
| 540 | # gSetRxChainmask1x1=0 |
| 541 | # These are defaulted to 0 with following definitions: |
| 542 | # 0: don't care |
| 543 | # 1: use chain 0 |
| 544 | # 2: use chain 1 |
| 545 | # 3: can use either chain |
| 546 | tx_chain_mask_2g=0 |
| 547 | rx_chain_mask_2g=0 |
| 548 | tx_chain_mask_5g=0 |
| 549 | rx_chain_mask_5g=0 |
| 550 | |
Srinivas Girigowda | 5abc707 | 2018-04-11 07:26:28 -0700 | [diff] [blame] | 551 | gForce1x1Exception=0 |
| 552 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 553 | #IPA config is a bit mask and following are the configurations. |
| 554 | #bit0 IPA Enable |
| 555 | #bit1 IPA PRE Filter enable |
| 556 | #bit2 IPv6 enable |
| 557 | #bit3 IPA Resource Manager (RM) enable |
| 558 | #bit4 IPA Clock scaling enable |
| 559 | #bit5 IPA uC ENABLE |
| 560 | #bit6 IPA uC STA ENABLE |
Srinivas Girigowda | 2596f79 | 2018-06-18 17:00:48 -0700 | [diff] [blame] | 561 | #bit7 IPA Real Time Debugging |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 562 | gIPAConfig=0x7d |
| 563 | gIPADescSize=800 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 564 | |
| 565 | #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period |
| 566 | #where we send NULL frame. |
| 567 | |
| 568 | #gApLinkMonitorPeriod = 10 |
| 569 | #gGoLinkMonitorPeriod = 10 |
| 570 | |
| 571 | #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. |
| 572 | #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. |
| 573 | gGoKeepAlivePeriod = 20 |
| 574 | gApKeepAlivePeriod = 20 |
| 575 | |
| 576 | ############################################# |
| 577 | # SAP related configurations |
| 578 | ############################################# |
| 579 | #Enable OBSS protection |
| 580 | gEnableApOBSSProt=1 |
| 581 | |
| 582 | #Enable/Disable UAPSD for SoftAP |
| 583 | gEnableApUapsd=1 |
| 584 | |
| 585 | # SAP auto channel selection configuration |
| 586 | # 0 = disable auto channel selection |
| 587 | # 1 = enable auto channel selection, channel provided by supplicant will be ignored |
| 588 | gApAutoChannelSelection=0 |
| 589 | |
| 590 | #SOFTAP Channel Range selection |
| 591 | gAPChannelSelectStartChannel=1 |
| 592 | gAPChannelSelectEndChannel=11 |
| 593 | |
| 594 | # SAP Country code |
| 595 | # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. |
| 596 | # Example |
| 597 | # US Indoor, USI |
| 598 | # Korea Outdoor, KRO |
| 599 | # Japan without optional byte, JP |
| 600 | # France without optional byte, FR |
| 601 | #gAPCntryCode=USI |
| 602 | |
| 603 | # DFS Master Capability |
Isaac Chiou | 502830c | 2021-07-29 18:54:57 +0800 | [diff] [blame] | 604 | gEnableDFSMasterCap=0 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 605 | |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 606 | #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled |
| 607 | gAPAutoShutOff=0 |
| 608 | |
| 609 | # Remove Overlap channel restriction |
| 610 | gEnableOverLapCh=0 |
| 611 | |
| 612 | # Enable/Disable channel avoidance for SAP in SCC scenario |
| 613 | # 0 - disable |
| 614 | # 1 - enable |
| 615 | gSapSccChanAvoidance=0 |
| 616 | |
| 617 | #Enable/Disable Tx beamformee in SAP mode |
| 618 | gEnableTxBFeeSAP=1 |
| 619 | |
| 620 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 621 | |
| 622 | #Enable/Disable dual MAC feature |
| 623 | # 0 - enable DBS |
| 624 | # 1 - disable DBS |
| 625 | # 2 - disable DBS for connection but keep DBS for scan |
| 626 | # 3 - disable DBS for connection but keep DBS scan with async |
| 627 | # scan policy disabled |
| 628 | # 4 - enable DBS for connection as well as for scan with async |
| 629 | # scan policy disabled |
Isaac Chiou | d4cd7cc | 2018-11-21 17:44:02 +0800 | [diff] [blame] | 630 | # 5 - enable DBS for connection but disable dbs for scan. |
| 631 | # 6 - enable DBS for connection but disable simultaneous scan from |
| 632 | # upper layer (DBS scan remains enabled in FW). |
| 633 | gDualMacFeatureDisable=6 |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 634 | |
Roshan Pius | 842c071 | 2018-02-15 08:57:51 -0800 | [diff] [blame] | 635 | # Turn on STA + AP/STA |
| 636 | gEnableConcurrentSTA=wlan1 |
| 637 | |
Srinivas Girigowda | 9f16f54 | 2018-05-29 14:28:33 -0700 | [diff] [blame] | 638 | # 0 - Disallow STA+SAP SCC on LTE coex channel |
| 639 | # 1 - Allow STA+SAP SCC on LTE coex channel |
| 640 | g_sta_sap_scc_on_lte_coex_chan=1 |
| 641 | |
Srinivas Girigowda | 4450413 | 2018-01-18 23:34:50 -0800 | [diff] [blame] | 642 | #Set priority for connection with bssid_hint |
| 643 | g_is_bssid_hint_priority=0 |
| 644 | |
| 645 | gdbs_scan_selection=5,4,1,16,4,1 |
| 646 | |
| 647 | enable_11d_in_world_mode=1 |
| 648 | |
Poddar, Siddarth | 541bac4 | 2018-03-12 16:38:50 +0530 | [diff] [blame] | 649 | gDptraceConfig=1,4,1,126 |
Srinivas Girigowda | d23abf6 | 2018-03-19 15:54:27 -0700 | [diff] [blame] | 650 | |
| 651 | ############################################# |
| 652 | # MAWC related configurations |
| 653 | ############################################# |
| 654 | |
| 655 | # MAWCEnabled - Enable/Disable Motion Aided Wireless Connectivity Global |
| 656 | MAWCEnabled=0 |
| 657 | |
| 658 | # mawc_roam_enabled - Enable/Disable MAWC during roaming |
| 659 | mawc_roam_enabled=0 |
| 660 | |
| 661 | # Enable/Disable the Motion Aided Wireless Connectivity |
| 662 | # based NLO using this parameter |
| 663 | mawc_nlo_enabled=0 |
| 664 | |
| 665 | #Enable/Disable chain selection optimization for one chain dtim |
| 666 | #Min: 0 |
| 667 | #MAX: 30 |
| 668 | gEnableDTIMSelectionDiversity=3 |
| 669 | |
Srinivas Girigowda | 5abc707 | 2018-04-11 07:26:28 -0700 | [diff] [blame] | 670 | # Enable/Disable rtt sta mac randomization |
| 671 | enable_rtt_mac_randomization=1 |
| 672 | |
Srinivas Girigowda | d23abf6 | 2018-03-19 15:54:27 -0700 | [diff] [blame] | 673 | gAP11ACOverride=0 |
| 674 | |
Srinivas Girigowda | 5abc707 | 2018-04-11 07:26:28 -0700 | [diff] [blame] | 675 | channel_select_logic_conc=0x0 |
| 676 | |
| 677 | gConfigVCmode=0 |
| 678 | |
| 679 | wlm_latency_flags_moderate=0 |
| 680 | wlm_latency_flags_low=0 |
| 681 | wlm_latency_flags_ultralow=0 |
| 682 | |
| 683 | oce_sta_enable=0 |
| 684 | oce_sap_enable=0 |
| 685 | num_oce_wan_slots=0 |
| 686 | oce_wan_score_idx7_to_4=0 |
| 687 | oce_wan_score_idx11_to_8=0 |
| 688 | oce_enable_rssi_assoc_reject=0 |
Srinivas Girigowda | d23abf6 | 2018-03-19 15:54:27 -0700 | [diff] [blame] | 689 | |
Srinivas Girigowda | 7bcc435 | 2018-04-05 16:27:35 -0700 | [diff] [blame] | 690 | # Enable/Disable rtt sta mac randomization |
| 691 | enable_rtt_mac_randomization=1 |
| 692 | |
Srinivas Girigowda | 83805b8 | 2018-05-01 15:05:44 -0700 | [diff] [blame] | 693 | #Enable/Disable Secondary Retry Rate feature subset |
| 694 | gEnableSecondaryRate=0x17 |
| 695 | |
Roger Wang | d5b18e4 | 2019-01-16 16:55:31 +0800 | [diff] [blame] | 696 | #Timer waiting for interface up from the upper layer |
| 697 | gInterfaceChangeWait=1000 |
| 698 | |
Sunil Ravi | 0ed51c1 | 2019-03-25 14:48:03 -0700 | [diff] [blame] | 699 | #Enable Bmps(power save in connected state) based on timer |
| 700 | #Timer value is in seconds |
| 701 | gAutoBmpsTimerValue=90 |
| 702 | |
Sunil Ravi | 136f067 | 2020-03-04 13:16:14 -0800 | [diff] [blame] | 703 | #Enable/Disable 802.11ai FILS support |
| 704 | g_is_fils_enabled=0 |
Chris Fries | 9c305b2 | 2017-06-27 12:37:49 -0500 | [diff] [blame] | 705 | END |
| 706 | |
| 707 | # Note: Configuration parser would not read anything past the END marker |