[libata] sata_svw: Disable ATAPI DMA on current boards (errata workaround)
Current Broadcom/Serverworks SATA boards (including Apple K2 SATA)
have problems with ATAPI DMA, so it is disabled. ATAPI PIO, ATA PIO,
and ATA DMA continue to work just fine.
Acked-by: Anantha Subramanyam <ananth@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c
index db32d15..d89c959 100644
--- a/drivers/ata/sata_svw.c
+++ b/drivers/ata/sata_svw.c
@@ -56,6 +56,8 @@
#define DRV_VERSION "2.0"
enum {
+ K2_FLAG_NO_ATAPI_DMA = (1 << 29),
+
/* Taskfile registers offsets */
K2_SATA_TF_CMD_OFFSET = 0x00,
K2_SATA_TF_DATA_OFFSET = 0x00,
@@ -83,11 +85,33 @@
/* Port stride */
K2_SATA_PORT_OFFSET = 0x100,
+
+ board_svw4 = 0,
+ board_svw8 = 1,
+};
+
+static const struct k2_board_info {
+ unsigned int n_ports;
+ unsigned long port_flags;
+} k2_board_info[] = {
+ /* board_svw4 */
+ { 4, K2_FLAG_NO_ATAPI_DMA },
+
+ /* board_svw8 */
+ { 8, K2_FLAG_NO_ATAPI_DMA },
};
static u8 k2_stat_check_status(struct ata_port *ap);
+static int k2_sata_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ if (qc->ap->flags & K2_FLAG_NO_ATAPI_DMA)
+ return -1; /* ATAPI DMA not supported */
+
+ return 0;
+}
+
static u32 k2_sata_scr_read (struct ata_port *ap, unsigned int sc_reg)
{
if (sc_reg > SCR_CONTROL)
@@ -313,6 +337,7 @@
.check_status = k2_stat_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
+ .check_atapi_dma = k2_sata_check_atapi_dma,
.bmdma_setup = k2_bmdma_setup_mmio,
.bmdma_start = k2_bmdma_start_mmio,
.bmdma_stop = ata_bmdma_stop,
@@ -359,6 +384,8 @@
struct ata_probe_ent *probe_ent = NULL;
unsigned long base;
void __iomem *mmio_base;
+ const struct k2_board_info *board_info =
+ &k2_board_info[ent->driver_data];
int pci_dev_busy = 0;
int rc;
int i;
@@ -424,7 +451,7 @@
probe_ent->sht = &k2_sata_sht;
probe_ent->port_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_MMIO;
+ ATA_FLAG_MMIO | board_info->port_flags;
probe_ent->port_ops = &k2_sata_ops;
probe_ent->n_ports = 4;
probe_ent->irq = pdev->irq;
@@ -441,7 +468,7 @@
/* different controllers have different number of ports - currently 4 or 8 */
/* All ports are on the same function. Multi-function device is no
* longer available. This should not be seen in any system. */
- for (i = 0; i < ent->driver_data; i++)
+ for (i = 0; i < board_info->n_ports; i++)
k2_sata_setup_port(&probe_ent->port[i], base + i * K2_SATA_PORT_OFFSET);
pci_set_master(pdev);
@@ -469,11 +496,11 @@
* controller
* */
static const struct pci_device_id k2_sata_pci_tbl[] = {
- { PCI_VDEVICE(SERVERWORKS, 0x0240), 4 },
- { PCI_VDEVICE(SERVERWORKS, 0x0241), 4 },
- { PCI_VDEVICE(SERVERWORKS, 0x0242), 8 },
- { PCI_VDEVICE(SERVERWORKS, 0x024a), 4 },
- { PCI_VDEVICE(SERVERWORKS, 0x024b), 4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0240), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0241), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x0242), board_svw8 },
+ { PCI_VDEVICE(SERVERWORKS, 0x024a), board_svw4 },
+ { PCI_VDEVICE(SERVERWORKS, 0x024b), board_svw4 },
{ }
};