opti621: add PIO 4 support
* Add PIO 4 support.
While at it:
* Use a single struct ide_port_info instance for OPTi621 and OPTi621X.
Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/drivers/ide/pci/opti621.c b/drivers/ide/pci/opti621.c
index 8c715b7..725c805 100644
--- a/drivers/ide/pci/opti621.c
+++ b/drivers/ide/pci/opti621.c
@@ -90,16 +90,6 @@
#include <asm/io.h>
-//#define OPTI621_MAX_PIO 3
-/* In fact, I do not have any PIO 4 drive
- * (address: 25 ns, data: 70 ns, recovery: 35 ns),
- * but OPTi 82C621 is programmable and it can do (minimal values):
- * on 40MHz PCI bus (pulse 25 ns):
- * address: 25 ns, data: 25 ns, recovery: 50 ns;
- * on 20MHz PCI bus (pulse 50 ns):
- * address: 50 ns, data: 50 ns, recovery: 100 ns.
- */
-
#define READ_REG 0 /* index of Read cycle timing register */
#define WRITE_REG 1 /* index of Write cycle timing register */
#define CNTRL_REG 3 /* index of Control register */
@@ -150,13 +140,13 @@
u8 tim, misc, addr_pio = pio, clk;
/* DRDY is default 2 (by OPTi Databook) */
- static const u8 addr_timings[2][4] = {
- { 0x20, 0x10, 0x00, 0x00 }, /* 33 MHz */
- { 0x10, 0x10, 0x00, 0x00 }, /* 25 MHz */
+ static const u8 addr_timings[2][5] = {
+ { 0x20, 0x10, 0x00, 0x00, 0x00 }, /* 33 MHz */
+ { 0x10, 0x10, 0x00, 0x00, 0x00 }, /* 25 MHz */
};
- static const u8 data_rec_timings[2][4] = {
- { 0x5b, 0x45, 0x32, 0x21 }, /* 33 MHz */
- { 0x48, 0x34, 0x21, 0x10 } /* 25 MHz */
+ static const u8 data_rec_timings[2][5] = {
+ { 0x5b, 0x45, 0x32, 0x21, 0x20 }, /* 33 MHz */
+ { 0x48, 0x34, 0x21, 0x10, 0x10 } /* 25 MHz */
};
drive->drive_data = XFER_PIO_0 + pio;
@@ -209,30 +199,22 @@
.set_pio_mode = opti621_set_pio_mode,
};
-static const struct ide_port_info opti621_chipsets[] __devinitdata = {
- { /* 0 */
- .name = "OPTI621",
- .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
- .port_ops = &opti621_port_ops,
- .host_flags = IDE_HFLAG_NO_DMA,
- .pio_mask = ATA_PIO3,
- }, { /* 1 */
- .name = "OPTI621X",
- .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
- .port_ops = &opti621_port_ops,
- .host_flags = IDE_HFLAG_NO_DMA,
- .pio_mask = ATA_PIO3,
- }
+static const struct ide_port_info opti621_chipset __devinitdata = {
+ .name = "OPTI621/X",
+ .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} },
+ .port_ops = &opti621_port_ops,
+ .host_flags = IDE_HFLAG_NO_DMA,
+ .pio_mask = ATA_PIO4,
};
static int __devinit opti621_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
- return ide_setup_pci_device(dev, &opti621_chipsets[id->driver_data]);
+ return ide_setup_pci_device(dev, &opti621_chipset);
}
static const struct pci_device_id opti621_pci_tbl[] = {
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
- { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 },
+ { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 0 },
{ 0, },
};
MODULE_DEVICE_TABLE(pci, opti621_pci_tbl);